20 Most Recent
Fujitsu 18R1 Air Conditioner Questions & Answers
1 Answer
How to remove cover on fujitsu split system head
The front cover can be dismantled (taken off as one Piece) by unscrewing the screws at the bottom of the air outlet (they are covered by screw cvers which will need to be taken off. Then just pull off the cover. PLEASE NOTE that the front panel (liftable to take out filters) will need to be removed lift up until 90 degrees and then pull off gentley and also take out filters before removing front cover
I take the time to answer you questions so please rate me
Thankyou
Mat
Fujitsu 18R1 Air...
|
Answered
on Nov 21, 2013
1 Answer
Fujitsu fan is loaded with
Hi,
Taking it out is a very difficult process and if you try you will wish that you didn't...I don't know which end of the globe you live in, but hopefully you are in the northern hemisphere, so you are approaching winter and will not need it...
Once cooling is over, take a small spray bottle and fill it half full of Clorox unscented bleach and the other half water...then spray the fan, soaking it well with the bleach water and moving it around by hand so that you get the whole fan...make sure to catch any run off and protect walls, carpets and such from the over spray, so you don't bleach them...
Then let everything sit and dry out....a few days should do the trick...then take compressed air and blow the dried residue that is left out of the fan blades...
Now you have a clean mildew free fan again...
heatman101
Fujitsu 18R1 Air...
|
Answered
on Sep 25, 2011
1 Answer
How do I remove front cover of Fujitsu indoor unit
THE INTAKE GRILLE REMOVAL
(1) Open the intake grille.
(2) Pull down the knob.
(3) Lift the intake grille upward, until the axle at the top of the intake
grille is removed.
THE FRONT PANEL REMOVAL
(1) Remove intake grille (Reference the intake grille removal.)
(2) Remove four screws.
(3) The thumb is hung on the lower part as shown in the figure,
and it pulls to the front, pushing [-] mark , and bottom hooks
(two position) is removed from wall hook bracket.
(4) The front panel bottom is pulled to the front, and bottom hooks
is removed indoor unit.
(5) The front panel is pulled to the front, raising the upper surface,
and a front panel is removed.
Fujitsu 18R1 Air...
|
Answered
on Jul 15, 2010
1 Answer
I want to remove the system from the house which
Hi, It is a 25,000 dollar find to bleed off the freon. This is why we have recovery machines. You can pump it down and save the freon that is in the whole system. Go to the outdoor unit. Leave the power on. The small copper line where it comes out of the unit will have a valve on it. It may have a cap screwed over its top. you will see an allen head screw on it. This may take a little time but is well worth it. Screw it down closed, CW. tight. Start the ac and let it run.Since you have no gauges to watch it pull the freon from inside the house to store it all in the outdoor unit, the condenser will shut down when it is done. Once the valve is off and you turn on the stat to run, it won't take very long for the freon to pump in the outdoor unit. We call this pumping the unit down. When done, close down the valve on the large copper line the same way before you shut off stat. Now, you save youself some $ as the freon can be used again. It is perfectly good. The tech will need to cut the lines and relocate them where ever you move this unit and resolder them with silver solder15%. New control wire and move electrical. I hope this has helped you. This is the way it is done. Keep me posted. Merry Christmas,
Shastalaker7
Fujitsu 18R1 Air...
|
Answered
on Dec 24, 2009
Not finding what you are looking for?
