20 Most Recent NorStar Meridian M7310 Phone - Page 8 Questions & Answers

familirize with devices user manual whether has feature functions requested. Second, ascertain that device was least malfunctioning since acquired. normally, familirising with innovative devices makes expertise in functionality.

Programming is done on 7310, 7324 and 7316 type sets.
Enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the show key (top right arrow).
The display should now ask for an extension number. Enter extension number you want to change the name on.
Press the show key (top right arrow)
The display should say LINE ACCESS
Press the next key (bottom right arrow) .
The display should say CAPABILITIES.
Press the next key (bottom right arrow) .
The display say Name.
press the Chng soft key.
use the dial pad to enter the name. advance using the arrow soft key to go to the next letter
ex. Bill = 2,2 -> 4,4,4 -> 5,5,5 -> 5,5,5
Press the next key (bottom right arrow) to enter the name.
Press the release key when finished

Mostly this happens when the unit has been used by someone else. Most fairly used units or refurbished units encounter this. Mailboxes are meant to be for rivate use therefore when a password is set on it the feature 983 do not work on it because a password has already been set.
Usually what i advice is for you to take it to the dealer and make an official complaint often times they would replace the system processing memory and once this is done although all previous information on the unit will be lost but you wont have the problem of a locked mailbox. Other than this unless you find who put the password and ask them what it is. This problem could also have been caaused by poor programming of the unit initially.
Hope this solution has been helpful?
Thank you for visiting FixYa.

Of course it's possible, however, you need to turn off Auto Set Relocation. I'm not sure if it's an Administrator or only an Installer function.

There is a trick....and I've never tried it because I HATE ASR, if you unplug the old phone, move it to the original location, and wait at least 5 minutes, then unplug it from the original location and plug in the NEW phone before you plug in the phone you just unplugged, the new phone will become the old extension and your original phone will be unprogrammed. It also says you have to wait at least one minute before you can change the DN of a new phone, but that requires INSTALLER access.

Like I said......

Carl
.

From the idle 7310, press FEAT *2 the button and dial their extension.

If you get a nasty notification, like Denied in Admin, or Set Locked, you'll need the system administrator password and procedure to unlock the phone..

Carl

A defaulted system has 2 lines assigned until you program them. It's programmed from the installation manual of the phone system. There, under Terminals & Sets, you tell the system how many intercom paths, whether it's handsfree, and how many lines are assigned. Once you fill in all the information, you can Copy the set to all the other sets and you're done.

Carl

Does it work on handsfree or with the handset ? It should work for one of those. Make sure your handset isn't plugged into the headset port on the bottom of the telephone. If it's still not working, change the handset and curly cord with one from another phone to test if that's the issue. (but then the Handsfree should technically work)

This should work on M7310, M7324 & T7316

Feature ** 266344 - password 266344 - configuration - line data - line access - show ext (yours) - line assignment ( which lines you have, usually 1 & 2) - show line - appear only/ring/apprear and ring

Hope this helps

If you plug the telephone into an activated (connected to the Norstar System) telephone jack, the lights should begin to blink while the phone boots-up. The system automatically assigns an extension number. To see what the ext. # assigned to the phone is, press "Feature * 0" (Button Inquiry) and press an intercom button. This will display the ext, # and Set Name of the phone.
Good Luck!

In the mailbox setup, there's a prompt called EXT .. make sure your extension number is there. There's another prompt called MSG WAIT (or something like that) which needs to be set to YES or Y. The person that setup the mailbox should be able to get to these settings.

First of all, make sure you're plugged into the headset port of the telephone and not the handset port. Pressing the Handsfree button should change from handset to headset. You can't use the speaker phone with the headset plugged in.

Depends on which system you have. M7310 is just the phone model which is compatible with all norstar meridian systems.

The easiest way (which only works on one of the phone system models) is to dial Feature ** TIME
and use 23646 as the password. If feature **TIME doesn't work for you, it might be best to do it with someone over the telephone since it can be slightly tricky.

What? They are either programmed or not programmed. If the button is blank, I'm voting for NOT programmed.

If your system is old enough, it's probably lost the backup battery. Ugly things, like pulse dial and only 2 lines are what usually happens, along with losing all of the button mapping but your 2 lines and the default programs of LNR, CONF, etc.

If it's just one phone, there's no magic recall. You'll just have to reprogram it. Same with the system if you've lost everything, but I"d call a repair tech first to fix the battery on the software cartridge.

Carl

1st check to see that the feature is turned on. More than likely you have a asterisk/elastix style pbx. You might have performed an update and the defaults might have changed.

To change # of rings you have to go into programing OK press feature * * on the main set and config (266344) then the password admin (23646) this goes to terminals and sets hit show and enter the set you want to change go to capabilities this will allow you to chang # of rings on that set

Insure that the phone line is plugged in firmly. also, follow the phone line down to the other end (the end NOT connecting to your phone) and make sure that it is firmly connected there as well.

Thanks and hope this helps! please rate if it does.