Jet 10" Xacta Saw Left Tilting Arbor Tablesaw 708661 - Answered Questions & Fixed issues

First guess would be a lock bolt is tightened down. Second guess would be a 90 degree latch or stop. Take a look at this link from "mikestools": http://www.mikestools.com/download/Jet-Owners-manuals/Jet%20Tablesaws/708661.pdf.

Sounds like it should be. What do your local regulations tell you that you need? If in doubt consult a professional and check the code.

my table saw jet model jtas-10-1 serial # 9031109 stock # 708510

google jet band saw jwbs-18 manual. there several sites including manufacture

hi jason. this is all i could find,go to this link and have a look. diagram of Jet 200336 Indicator Bar Google Search

I would guess pitch or just saw dust in the gears. I have had on my saw that i cranked it up just a little to much and it locked up on the gear. I ended up taking the blade out and loosened the gears and shaft on the tilting mechanism to relief the pressure. Put it back together and it worked fine.

I am not sure what model you have but they have this saw in two models one is 230 volt only the other is 230/460 volt. But that is not a 220 volt circuit. 220 volt is single phase where the 230/460 is a 3 phase circuit. Look on your motor and see what the power requirement is. if you have a different machine then the one I am looking at I would switch over to the auto function.

If you have not supplied enough power (like using an extension cord) the motor sees a big voltage drop, starts drawing a lot of current and eventually overheats. Make certain to use a good supply. JET Tools

There should be 2 handles: height and tilt. Tilt is typically located perpendicular to the blade on the base of the saw.

Call bandsawparts.com . They have aftermarket band saw tires.

You should check your manual. There's a blade tension handle on my bandsaw, which is adjusted every time I need to change tension or change blade. There ways how to check the correct tension, you can pluck the blade like a string on a guitar and if you hear music not like sound, tension is good. Or you can follow the suggestion blade tension on your saw. or you may also use tension gauge.

If the motor isn't HOT when it kicks out you need to replace the thermal sensor is all. If it IS, then the motor needs replacing.

you can download the manual from this sitewww2.woodcraft.com/pdf/708100.pdf

Please look for Jet parts at this link. You can search for your model at this page, and from there choose "find out more" to navigate to the parts list to obtain the part number you need. If yours is a JTAS-10 see this link, page 14-10.I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread. If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

Hi Kenneth,

My advice would be to send it back. Any repairs you attempt would void your warranty.

Handie Andie

Hi,

The Jet service agent in your area is:

Gator Repair (A. A. Casey)
5124 Nebraska Ave
Tel: 8132348831

Hope this helps!

Hi,
Does the blade still turn freely?? if not then yes... check the bearings... but if it turns easily then the bearings are okay...

Check the blade.... that wood can take the edge off rather quickly and I would try a new blade next....it may seem to be okay but still not cut well...

heatman101

Hi!
It depends.. what king of account is it?
yahoo? facebook?
Post back

Hi,
This may or may not be relavant... but you did not mention that you checked the blade(s)....have you tried even a diferent make of blade??? Seems like you went over everything on the saw... just questioning the only thing that seeems left to check...

heatman101

Jet's manual site is here. I didn't find that exact model number. It might be worth double checking.

If this post was useful, please vote. Thanks!