20 Most Recent RCA 25414RE3 Corded Phone Questions & Answers


Check the cor and cos setting of the phone It shold have the permissions to call outside

RCA 25414RE3... | Answered on Feb 28, 2018


Each of the six phones must have line 1 connected to the same "subscriber loop" (the same phone number). Assuming this is the case, and that you have not assigned any numbers to the the top six speed-dial buttons, each station will have agreed to be assigned a station number.

From any station, pressing the speed-dial button for another station's station number will page that station.

Now, how to properly initiate an intercom conversation differs between announcing to another station that a call is on hold, or a "cold call".

RCA 25414RE3... | Answered on Dec 15, 2016


This is an equipment problem that should be referred to RCA.

RCA 25414RE3... | Answered on Jul 25, 2016


~*~*~ SOLVED SOLVED SOLVED! ~*~*~ After talking to both ATT and RCA with no success...I figured it out. ~*~*~ Plug your phone line into the "DATA PORT" on the back of the unit. Slide the "DATA PORT" switch to whichever line is showing it has a message. Press the corresponding Line# button on the front of the phone. (you should hear the dial tone) Dial your voice mail number. Let it answer, (enter your passcode if needed), then hang up! - That's it! example: MSG Waiting:L2 - I plugged the phone line into the Data Port and moved the data port switch to "2". I pressed LINE 2 on the front of the phone, dialed my voice mail number, it answered, I put in my passcode. (It said that I did not have any new voice mails), then hung up! That's it! Message Indicator light off!!! Repeat for each line that shows a (false) message waiting. ~~~Don't forget to move your phone line back into it's correct port on the back of your phone.~~~

RCA 25414RE3... | Answered on Sep 02, 2015


You apparently have unheard messages on the voicemail system provided by your telephone company. This system records messages when someone calls while you're already on the phone. Please contact your telephone company for instructions on accessing their voicemail system.

RCA 25414RE3... | Answered on Aug 15, 2014


Don't know about other models, but I just called RCA small business phone support (800-511-3180) to find out how to clear the message light indicator on my 25210 2-line cordless phone when it continues to blink but there is no message.

All you have to do is hold down the delete button for a few seconds and it will clear. Hope this helps someone else from going batty!

RCA 25414RE3... | Answered on Dec 22, 2012


You can find the combiner at Radio Shack Model: T07843 ' Catalog #: 55034722. It may only be online not in the stores.

RCA 25414RE3... | Answered on Nov 15, 2012


hi its hard to understand... the phone is connected to line 4 or not? if so and line 4 is dedicated to fax line then the fax tone is the cause of your confusion fax tone is different from a regular tone phone if the phone isnt connected to line 4 and only to all 3 ordinary lines - then the phone is getting a over volage from them and activates the light & messege alert my advice let it be you will start playing with it something else will go worng... good day

RCA 25414RE3... | Answered on Nov 15, 2012


The only thing you can do is unplug the unit from the wall and from the phone line. wait over night and see if this resets the unit. if it does not, I,m afraid there is a circuit problem in the phone and most likely will not be worth repairing, but try to hard reset like I said first. good luck

RCA 25414RE3... | Answered on Dec 28, 2011


There are a couple of problems you may have.

First, the wall jack may not be wired correctly or the wire you ar eusing is a single line wire.

The easiest to check is the wire, look at the plug and see if it has 4 copper leads. If it only has two in the middle two slots then it will only connect line 1. If it has 4 copper leads then it should pass both lines 1 and 2 (or three and four). The middle leads are line 1 and the outer two are line 2.

If the wires all check out then you may have a wall plate that is not wired for multiple lines on the single wire. That will require a technician coming out and rewiring the plate. There are also adaptors available at Radio Shack that will combine two lines to one wire if you have both lines on the wall plate.

I have a blog on 4 line phones if you would like other tips about them. Go to the tag cloud and you will see 4 line phone.

RCA 25414RE3... | Answered on Dec 05, 2011

Not finding what you are looking for?
Lands Phones Logo

71 questions posted

Ask a Question

Usually answered in minutes!

Top RCA Lands Phones Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Cindy Wells

Level 3 Expert

6073 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a RCA Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

RCA Lands Phones

  • RCA Lands Phones

Most Popular Question

new message light stop flashing

  • Lands Phones
Loading...