20 Most Recent Xerox Phaser 7760 Laser Printer - Page 3 Questions & Answers

Magenta toner(s) not being recognized, I looked into the little slot on printer where chip slides in and found one of the four contacts was bent up out of position. Rather than risk further damage by poking it in such a confined space I am going to remove the part first.

rror codes If the printer's front panel displays a message Error XX, find the error code in this table and follow the instructions for resolving the problem. If problems persist, check the Xerox web site www2.tek.com/TekSMART/ or contact service. Error User Corrective Action Error 01

• Remove and re-install the black Toner Cartridge, then turn the printer off and on.
• Replace the black Toner Cartridge, then turn the printer off and on.

Error 02

• Remove and re-install the cyan Toner Cartridge, then turn the printer off and on.
• Replace the cyan Toner Cartridge, then turn the printer off and on.

Error 03

• Remove and re-install the magenta Toner Cartridge, then turn the printer off and on.
• Replace the magenta Toner Cartridge, then turn the printer off and on.

Error 04

• Remove and re-install the yellow Toner Cartridge, then turn the printer off and on.
• Replace the yellow Toner Cartridge, then turn the printer off and on.

Error 05, 10, 11,12, and 13

• Turn the printer power off, then on.

Error 20

• Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
• Remove and re-install the Main Charge Grid. Turn the printer off, then on.
• Remove and re-install the Transfer Kit. Turn the printer off, then on.
• Remove and re-install each of the Toner Cartridges. Turn the printer off, then on.
• Replace the Main Charge Grid. Turn the printer off, then on.
• Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
• Replace the Transfer Kit. Turn the printer off, then on.
• Replace the Toner Cartridges. Turn the printer off, then on.

Error 21, 22, 30,and 32

• Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
• Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
• If a problem persists for Error 30, clean the sensor. See Cleaning Phaser 750 Printers.

Error 33

• Check for jammed paper throughout the paper path (especially in paper feeder).
• Remove and re-install the paper feeder and Transfer Kit. Turn the printer off, then on.

Error 40, 41, 42,and 43

• Check for jammed paper in the Fuser. Re-install the Fuser. Turn the printer off, then on.
• Make sure that you have the correct Fuser for your local printer power supply: 110-Volt Fuser Part Number 016-1839-00 220-Volt Fuser Part Number 016-1840-00
• Replace the Fuser. Turn the printer off, then on.

Error 50, 51

• Turn the printer off, then on.

Error 52

• Remove the Duplex Unit (if installed).
• Check for paper under the Upper Tray.
• Turn power off, then on.

Error 53

• Open left door and remove any jammed media.
• Tun the printer off, then on.

Error 60

• Remove the media from the Multi-Purpose Tray. Turn the printer off, then on.
• Reinstall the media. Make sure you do not overfill the tray.

Error 61

• Remove and re-install each Toner Cartridge. Turn the printer off, then on.
• Replace each Toner Cartridge. Turn the printer off, then on.

Error 62

• Check for jammed paper throughout the paper path (especially in the paper feeder and Fuser).
• Remove and re-install the Fuser. Turn the printer off, then on.
• Slide out and re-insert the paper feeder. Turn the printer off, then on.
• Replace the Fuser. Turn the printer off, then on.

Error 63

• Remove and re-install the Imaging Unit. Turn the printer off, then on.
• Replace the Imaging Unit. Turn the printer off, then on.

Error 70, 71, and72

• Turn the printer off, then on.

Error 73

• Remove and re-install the Imaging Unit. Turn the printer off, then on.
• Replace the Imaging Unit. Turn the printer off, then on.

Error 74

• Remove and re-install the Fuser. Turn the printer off, then on.
• Replace the Fuser. Turn the printer off, then on.

Error 80, 81, 82,83, and 84

• Make sure that all four toner cartridges are installed in the printer.
• Turn the printer off, then on.

Error 01p through Error 47p

• Make sure that installed memory DIMM(s) are compatible with printer's image processor board and that they are installed in the proper slot(s).
• you can helpful

C6000 km-1820.3gp - YouTube

? 0:55 www.youtube.com/watch?v=Ef0WwaTXgtQ Oct 6, 2010 - Uploaded by natasmanda01 Cancelamento dos codigos de erros c6000, c6400 e c6020 da kyocera ... HOW TO RESET AND HARD RESET KYOCERA HYDRO XTRM ...

Printer Resetter: Solving error C6000 on Kyocera Mita printers

pritner.blogspot.com/2013/08/solving-error-c6000-on-kyocera-mita.html Aug 8, 2013 - c6000. error. Error Message Check Ink U041 · Xerox WorkCentre C2424 DADF Error ... SSC Service Utility Software to reset Epson printers.

Depends on what country you are from ? Depends on if you want a geniune Xerox toner Cartridge or a compatible one ? Depends on capacity - 30,000 sheets if you get a smaller capacity it is cheaper but it is not the same as a 30,000 sheet capacity . check capacity when buying a toner . http://www.amazon.com/6R01182-Cartridge-CopyCentre-WorkCentre-006R01182/dp/B0027QW3GY http://www.myprintershop.ca/brand-new-original-xerox-6r1182-laser-toner-cartridge-black.html http://www.newegg.com/Product/Product.aspx?Item=N82E16828118961 http://www.pcrush.com/product/Toners/671778/Xerox-6R1182-Toner-Cartridge-Black http://salestores.com/xerox006r01102.html#.VyFWOfl97IU http://www.xerographic.co.uk/products/xerox-genuine-black-toner-cartridge-006r01182-6r1182-m123-m128-133.html http://www.precisionroller.com/6r1182-for-xerox/details_pn_38946.html http://www.myprintershop.ca/brand-new-original-xerox-6r1182-laser-toner-cartridge-black.html http://www.compredia.eu/xerox-toner-cartridge-black-006r01182-6r01182.html http://www.pcrush.com/product/Toners/671778/Xerox-6R1182-Toner-Cartridge-Blackhttp://salestores.com/xerox006r01102.html#.VyFXHvl97IU

Open the top cover, remove toner cartridge, jam should be below there. There's a common issue where the grey transport belt break underneath the toner cartridge, inspect those belts to make sure both are intact and not broken. A picture of the belt is at link below http://www.iteminconline.com/023n01310_023n01310-xerox-4600-belt-flat-rubber.htm

The MCU Board is overheating. If the room temperature is normal, replace the MCU Board. http://www.iteminconline.com/622s01684_960k39348-960k39347-960k39346-960k39345-960k39344-960k39343-622s01684-xerox-6280-mcu-board-engine-control.htm

That error is a printhead tilt fault. The printhead is not able to cam back and forth correctly. There is a kit that fixes that problem, part number 8570-Z1. http://www.iteminconline.com/itemdesc.asp?ic=8570-Z1&eq=&Tp=

Change the chip to a non-metered type.

Fixing temperature control startup error Temperature of the Fixing Assembly did not reach the specified temperature within the specified period of time. Remedy1. Check connectors on the fixing film unit. 2. Replace the fixing film unit. 3. Replace the engine controller PCB. for more help visit CBR Tech Solutions

Great answer, My error did not go away and it made me remove the entire ink loader tray and find that one of the metal spring clips came out of place and the heating element came off its place, Thank you Jose Cada so much for that answer. Here is the sequence to clear the error 04,025,46: ###(print count) on my 8860MFP: Press SYSTEM button on the dark center section of the control panel, select INFORMATION and then TROUBLESHOOTING then SERVICE TOOLS, when in service tools press and hold the up arrow while still pressing the up arrow press the down arrow. the display should say SERVICE . select ENTER DIAGNOSTIC MODE press enter, WAIT 20 seconds before display shuts off and goes into diagnostic mode, go to function menu. then go to clear ISC fault and enter. ISC=ink stick count fault.

Try a different cartridge. While line typically means that no toner is being applied to the drum in that location. Would also explain the squeaks.

Which model do you have?

The inkloader has gone bad, the error signifies that the yellow ink is unable to melt, part number 133K27770 http://www.iteminconline.com/itemdesc.asp?ic=133K27771&eq=&Tp=