Siemens 24 in. SE64A630GB Built-In Dishwasher - Answered Questions & Fixed issues
My dishwasher is sticks in between washing cycles
These mechanical timer machines have to follow a series of logical steps to complete the program - ie, empty. fill to level 1. wash. heat to temp. etc etc
My guess is the machine is not heating, as you say it works for part of the program - or possibly it is not emptying correctly? check water heating element and drain pump.
Program 4 eco is a separate program from 3, using low temperature washing - the machine does stop between 3 and 4 normally and doesnt carry on through.
Siemens dishwasher reset
power on. hold power scrub and delicate buttons (Cancel Drain) down for three seconds. Unplug and plug in again.
Top spinner not spinning
This is most likely because the seal for the top spray bar is bad/missing or has debris in it or in the pump.
My siemens dishwasher bottom arm does not spin to
Hi,
I
have an older dishwasher also and recently my wife also complained
about it not cleaning right... so me being the man I am tried in vain
to clean the things... Bought new spray arms online and installed
them in minutes...now the thing works like new... However I have also
found that if the heating element goes bad then that also can mess
things up bad... So I would buy new spray arms, and also check out
the heating element to make sure it is working... Here is a tip that
will help you with the online buying...
Dishwasher
Spray
Arms not Spinning
How
to Buy Appliance
Parts Online
A
bad heating element causes many problems in
dishwashers...
Dishwasher Problems The Heating
Element not Working
Dishwasher
Maintenance
Dishwasher
Residue and Film on Dishes
heatman101
Asker's Testimonial "explanation very clear. will give
it a go and see how simple it was. thanks Ronnie " -
ronnieshomes
My dishwasher isn't getting up
Hi,
I
have an older dishwasher also and recently my wife also complained
about it not cleaning right... so me being the man I am tried in vain
to clean the things... Bought new spray arms online and installed
them in minutes...now the thing works like new... However I have also
found that if the heating element goes bad then that also can mess
things up bad... So I would buy new spray arms, and also check out
the heating element to make sure it is working... Here is a tip that
will help you with the online buying...
Dishwasher
Spray
Arms not Spinning
How
to Buy Appliance
Parts Online
A
bad heating element causes many problems in
dishwashers...
Dishwasher Problems The Heating
Element not Working
Dishwasher
Maintenance
heatman101
Asker's Testimonial "explanation very clear. will give
it a go and see how simple it was. thanks Ronnie " -
ronnieshomes
Water pump works from the minute I press the main switch
I may have had the same problem. At the end of a normal wash cycle the pump would stay on for hours or even days - I would have to power off, and then keepp trying to power on until it had eventually stopped. The pump operates even with the door open.
Problem is caused by a small float which senses the water level in the dishwasher, floating up and operating a microswitch, which turns on the pump to pump the water out. Obviously, if the dishwashe is filling up for some reason, you want the pump to operate even if the door is open. The float is in a small chamber - a very snug fit, with a hole in the bottom which is connected to the main pipework in the machine. There is another chamber next to the flot chamber which is also connected to the pipework. When the water level rises too high, water from this second chamber overflows into the flot chamber, raising the float and operating the pump. The water level then drops as the water is pumped out. The water level in the float chamber should also drop, but didn't on my dishwasher because the hole in the bottom was blocked (with old soap suds and grime I assume). Hence the pump just stays on. I assume in my case, the water flowed out very slowly, and eventually the pump stopped.
To fix it, removed the left hand side panel (2 screws on the front door lip. The back of the panel is just hooked on some raised bits of plastic). This exposes all the pipework, and the red float can be seen in it's chamber. I removed an extra couple of bits of plastic near the float chamber whilst I tried to work out what to do - but this may not be necessary. You will have to try for yourself. I couldn't get access to the hole to poke something in to unblock it, so I poured sink and drain cleaner into the flot chamber, topping up as it drained away, leaving it for approx. 15 mins. I think thick bleach would also work. Note: this cleaner won't be very good for any metal inside the dishwasher, so run 1 or 2 wash cycles to clean it out.
Maybe the dishwasher cleaner advertised on tv would have worked i.e. the stuff you put in the dishwasher on an emty cycle to clean out all the internals. I haven't used it, but it would be easier than taking the dishwasher to pieces.
Hope this helps
Kenmore Elite Not Draining Water Completely
Check this link. Multiple causes are possible yet most is how drain is hooked up to disposal and back pressure built up. Hose must be installed correctly.
http://www.partselect.com/repair.aspx?appliance=dishwasher&part=water-wont-drain
Our Siemens dishwasher retains water and smells
I would check the bottom of the dishwasher to see if there are any bones, old food built up as some of these collection systems have a small disposer built into them.
If you find any food, it's probably that.
Also, you can make sure that the drain line is the proper length and high enough as this is a common problem. Do a good search on proper drain height for dishwasher.
You may run an empty load of dishes with a cup of bleach added to eliminate the odor as well. Bleach will kill any bacteria causing the smell. More than likely the drain hose wasn't installed correctly.
Water does not completely drain on Kenmore Elite.
Hi..
If your machine does not drain you need to check this
- Inspect the drain hose for kinks
- Test the timer control
- Test the lid switch (some models)
- Inspect the water pump
- Inspect the drive belt (belt drive only)
- Inspect the motor coupler
Before testing the lid switch, unplug the washer or shut off the power at the fuse box or breaker panel to avoid an electrical shock hazard.
Regards
PCmania
Water remains at the bottom of the dishwasher
some dishwashers have water left after the final rinse. it is important to keep the motor seals wet between loads. My filter is always immersed. If we go away for two weeks, I put 2 litres of water into the tub and let it soak 24 hr so that I never start it with dry seals.
Siemens SE64A630 GB I got a tingle up my arm
I would say it is an earthing problem, check over your earth wires, normally black and grey is neutral, check to make sure your earth wires are connected properly, and tight, better to completely turn appliance off by disconecting power plug while doing this, take care not to play around with the wires too much to prevent a nasty electric shock
SIEMENS SE64630GB NOT TAKING IN WATER
- hot water valve selinoid and cold water selinoid valve are magnetily operated valves located in the lower part of the dishwasher that need electricity-----
- wire loose?
- kinked supply hoses and
- my favorite is the valve at the kitchen sink angle stop is lying to you, indicates open but is really still shut (broken valve stem) or it has corroded shut .
Not finding what you are looking for?