Top 20 Porter Cable Portable Generator BSV750 Questions & Answers

The idle control switch allows the generator to go into idle when there is no demand form the appliances connected. This saves gas and increases the life of the generator. Damage can occur for some appliances like a refrigerator/freezer because the voltage and frequency are not prepared for the load resulting in a low voltage bad startup that will damage the appliance. Suggest that you leave the idle control switch off while any motor/electronic devices are connected. The throttle control is likely a choke function for starting. These generators are designed for only one running speed to produce the necessary 60 cycles per second and voltage. The following link is to a Canadian web site that later in the detail report describes the concern of idle control. In addition it provides good insight to the operation and use of portable generators Hope this helps? Understanding Portable Generators The user manual see pages: http://www.mikestools.com/download/Porter-Cable-Manuals/Porter-Cable-CTE300.pdf

We really need a complete model number to get to an IPL that has your parts. This generator has 4 variations Type 0, 1, 2, & 3.
(Type 1 link below)
http://www.ereplacementparts.com/porter-cable-bsv750w-type-gas-powered-generator-parts-c-129_1825_2153.html

Parts manual pdf: (Detail A)
http://www.ereplacementparts.com/images/Porter_Cable/BSV750-W_TYPE_1.pdf

Breakers are item 206:

206 Z-GS-0026 BREAKER CIRCUIT 125/ 1

206 Z-GS-0681 BREAKER CIRCUIT 125/ 1
206 Z-D21508 BREAKER CIRCUIT125/2 1

Thanks for choosing FixYa,
Kelly

here is the url for the parts site that porter-cable uses for consumer parts ordering
http://servicenet.deltaportercable.com/

Have you checked to ensure the GFI outlet is not tripped?

i beleive that this unit is a generator only,to flash it go to the armature and flash it there.

You need an multi meter, on the ohms scale. Short the two prongs on the cap out, removing any voltage on it. Put your meter to a mid range ohms scale. Touch the leads to the prongs on cap and watch your meter. It should start climbing in value and then go to 'OL' if it's digital. If it's an analog meter(with a needle) it will go all the way over to 'infinite. This means it's good.
If it's bad, it will just read 'OL' or go right to 'zero' meaning it's either shorted or open. If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

you should be able to do it by ear,With a load on the unit you should be able to idle it to where it sounds like it is not running to fast and that it is not running enough to keep it from triping the reset.it should sound smooth. or idle it to around 2000 rpms or lower.

just push the power then when th as motor not run it is break!

15/40 of a name brand

Question edited for clarity. Normally on the back or hidden inside https://www.google.com/search?q=iron+force+95+welder+fuse+location Seems to be an unknown make. Try the link where you live https://www.google.com/search?q=iron+force+95+welder+manual ..

To check if there is a signal from the switch on the gun, depress the switch and the wire should start to move out. If it does, the main board has a fault, if it doesn't, it may be a faulty switch.

Question edited for clarity. Some ideas in the link. https://www.google.com/search?q=Miller+250+welder%2C+brushes+unevenly+worn ..

https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&ved=2ahUKEwiJm8Xqtq6DAxUvrokEHSvtAyUQFnoECA4QAQ&url=https%3A%2F%2Fwww.fixya.com%2Fsupport%2Ft29927508-deltaweld_350_help_100_code&usg=AOvVaw1Zz2ud-ECJTvyBdf5Zm-bJ&opi=89978449

Question edited for a lot more clarity, 'make model (what it is)' in the correct order. The thing about Speech to Text, is that you MUST go back through it and add punctuation or it all runs into one sentence. I did that for you as well into what I think you thought you were saying! This is an antique from the early 1950s. There is a picture of the inside wiring here https://weldingweb.com/vbb/threads/703256-Old-Marquette-Welder-wiring-question Manual for a Model 60 and 60C https://www.ebay.com/itm/115540831572 More here https://www.google.com/search?q=Marquette++Model+64+Farm+Welder+wiring+diagram ..

Question edited for clarity and order. You can't. It is 400 volts - 3 Phase.

Cutmaster 25 Manual Plasma System

https://www.westermans.com > victor-thermal-dynamics... 25mm genuine cut, 30mm maximum cut, 38mm severance; Input: 3 ph. 400V 50/60Hz 20A; Output: 80A @ 40% DC; Front panel LED's indicate status conditions for ... https://www.google.com/search?q=Plasma+cutter+thermal+dynamics+25 ..

'this welder'. The one that only you know what it is?

Hi, please for damaged wires, check that a technician has blown out dust from the rear portion of your welder after dust has been removed and double check that you've cleaned the exterior within the last 2 months. Thank you.

125EN Manual.qxd (buffalotools.com) Copy the above link into a microsoft edge browser address bar and click on it. The user guide has a lot of photos about assembly. Perhaps one will be what you are looking for. Or if you are currently using Edge, just click on the link. Good luck. Otherwise, perhaps the guys at the following link might have a picture for you. Contact them: https://reviewmotors.co/chicago-electric-welding-replacement-parts/

Power supply short circuit, it blew the fuses out when it let go. https://www.google.com/search?q=migomag+220+no+arc ..

moved you out of cars to welders TIG dead. well see if breaker in shop tripped first.