20 Most Recent Bosch 1581AVSK Top Handle Jig Saw Kit Questions & Answers

This tool has no mechanism for the fixating ot the saw but only a short ***** part 53 its a fault in the manual , it simply replace the saw with a screwdriver. or simply the clamp ***** to release turn it loose and from the top you can replace the clamp ***** Bosch B4300 0601582535 Jig Saw Parts

To change the Bosch B4300 blade - If the grey knob does not turn to release the broken blade, you need to use a LONG THIN flathead screwdriver down the center hole at the top. Unscrew until the broken blade is loose. Pull out. Replace the new blade and then screw the it tight through the same hole at the top. DONE.

Hi Dave, Try the Bosch site at http://www.bosch-pt.com/boptmanuals/gb/en/index.jsp;jsessionid=CD238E0C373D87F9C2693A38909E1782.s035?
Thats where i found mine.

You betcha, got it right here:

http://mdm.boschwebservices.com/MDMCache/English%20[US]//t10/0000000/r00058v-1.pdf

Thanks for using FixYa.com
Farmerbear

Hello. where the blade enters the blade holder there is a screw. Unscrew it, turn counterclockwise, remove the screw and then remove the blade. Reinstall the new one and replace the screw. Joe

Here are some directions on installing the blade to ensure the proper procedure has been followed when installing.

1. Set the blade orbit selector lever to position III.
2. Fit the supplied screwdriver into the top plunger hole and loosen the internal blade securing screw about 3 to 4 turns counterclockwise.
3. Insert the blade into blade plunger at a 90° angle to the cutting direction. With a slight upward pressure, turn the blade teeth forward (direction of cut) and guide the back of the blade into the groove in the center of blade roller guide.
4. Pull gently down on the blade to seat the blade tabs in the plunger.
5. With the blade in the proper position, securely tighten the blade screw by turning the screwdriver clockwise.

I hope this helps. Please rate on how helpful the answer was. Good Luck and have a great weekend.

try freemanuals.com on the web

part number is 2 6034 00000 and list is 1.50, you can buy a replacement from Ereplacementparts.com or direct from Boschtools.com

YOu can download the user manual in the following links
http://mdm.boschwebservices.com/MDMCache/English%20[US]/t10/0000000/r00061v-1.pdf
https://www.boschtoolsservice.com/Order/IPL/IPLDetails.aspx?tn=0601587651&mn=1587AVS&init=1
The blade can be replaced by unscrewing the screw found on the shaft.

You need a long shafted flat head screwdriver that fits into the hole in the handle above the blade. Then simply loosen or tighten the screw inside there, and the blade twists 90 degrees and will pull completely out. Reverse to install. Also see pg 7 of instruction manual here.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

This sounds like the Hand crank mechanism could be the problem. If it is going down in steps the gearing on the height adjuster could be slipping and 'jumping' teeth. When was the last time you gave the table saw really deep clean? Sometimes dirty and sawdust can get inside this machine. Sawdust can soak up oil and lightweight grease drying out areas that need the oil. Give it a really good clean and see if there is access to add a small amount of oil to the moving table lift parts.

Hi, Please rotate your locking collar clockwise in order to reverse the jam. Please review page 9 of your manual in part 1 of "installing the blade". You can also reference figure 3 on that page. Thank you.

It sounds like you are having difficulty tightening the blade on your Bosch 1587vs jigsaw. To resolve this issue, first unplug the tool and lift up on the knob and loosen the spindle lock. Then insert the blade and push up slightly while doing so and twist to align the blade with the roller. Make sure to turn past resistance until it clicks. If the issue persists, you may need to replace the "clic" assembly, part #2-602-025-901.

Hi, It sounds like you've called all 3rd party locations. Please call Bosch directly and request the part. And if they don't have it in the U.S. then you can request the phone number for their international locations. The U.S. phone number is 1-800-944-2904. Otherwise, I would search on ebay and alibaba to find the part that you've mentioned. Thank you.

you tighten arbor nut with lock up. try using nut wrench and rock the arbor back and forth.