20 Most Recent Samsung CLX-3175FN Color Laser All-in-One Printer - Page 6 Questions & Answers

Change the temperature sensor from the fuser unit. There is no need to chang the fuser unit, it is expensive. I repair the sensor, it is a mechanical device who remains blocked.

you can clean it out.

first remove the power and remove the cartridge cover and inspect for tiny piece of paper remove the piece of paper or you can use an mild air blower to flush it out for that first remove the toner and use the air blower and clean the inside of the printer if there is any tiny piece of paper the paper get jammed often

press menu#1934menugo to machine testthen to shading testok.swich printer off and on.

first you can feel if the fuser get warm at the back of the unit. if not replace the fuser unit.

Hi,Did you do some changes in the toners recently. Are you inserting the toner correctly . Please reseat the toner once again and switch off the printer and restart it. Waiting for your comments.

Faint prints with Laser Printer usually occurs when the drum is full with the wasted ink (toner power) or when the Fuser Unit is not working correctly. First of all try cleaning the Drum and remove the wasted toner power. There should be an opening on one of the end of the drum. In some cases, it needs to be disassembled to remove the wasted inks.Also remove the fuser unit and clean the unit. Please handle it with care and never clean it when it's hot/warm. Only do this, after the printer is left turned off for about half an hour.If nothing is helpful, try with another/new drum or fuser, that will help you get to find out the exact cause of the problem.Good Luck.Thanks for using FixYa.

Hello, Gary.

You may have tried this already, but, disconnect all the cables, including the power cable. Hold the power button for 3 seconds. Then, replace all the cables and power on.

If still a problem, you'll probably need a replacement fuser sensor or the fuser itself has malfunctioned.

Hope this helps.

Hello.

Smeared toner happens because the nonstick coating on the fusing roller is scratched or has baked-on debris. You can try to clean it with a soft cloth and isopropyl alcohol, but make sure you let it cool down first.

Hope this helps.

I'd try the Image Unit (PN # CLPR300A) first.

Then perhaps the Cartridge Transfer Unit JC96-04840C
Whit
800-367-4836

go in your menu under m/c setup. you will find altijute ajs. shange that on higer if it is on normal or to high 1 if it is on high.

I have the same problem
Message: door open - but closed is several times
Cannot use my printer/copier - help
Already switched it off, cleaned the green roller
but got same message: door open
O.Kraaijeveld

Step 1
Turn the printer off and on to see if it can automatically clear some or all of the jam. Many printers provide an error-code listing on the front panel display for the area where the jam occurred. If your printer shows an error code, be sure and check the printer manual to see if that identifies the area of the printer where the jam occurred.
Step 2
Turn off the printer.
Step 3
Remove any paper trays. Inspect them for wrinkled or damaged paper.
Step 4
Open any other doors that give access to the printer's paper path and to the toner or ink cartridge.
Step 5
If necessary, remove the toner or ink cartridge. Place it in a bag or away from light to avoid damaging it.
Step 6
If you find a piece of jammed paper, remove it by holding it with both hands and pulling firmly. The goal is to keep the paper from tearing. If several pieces are jammed together, try pulling out the middle piece first to loosen the jam.
Step 7
If the paper does tear, try rotating the roller gears manually to free the paper. Don't force anything, though.
Step 8
Replace the toner or ink cartridge and paper trays, close any doors you opened and turn the printer back on.
Step 9
If the printer paper jam message still appears, then there is still some paper in the printer. Inspect the paper path once again.

Pueden ser varias cosas. Problemas con los drivers (reinstalalos) Los cartuchos no son originales. El fusor encargado de fijar la tinta al papel esta dañado(remplazalo)

Bonjour cevale358 ,
Il n' y a malheureusement pas d' autre solution que de rentrer l' imprimante chez Samsung pour r?paration . Il s' agirait malheureusement d' une panne assez courante sur ce mod?le qui concerne le fusible et l' unit? d' alimantation .. Voici quelques pr?cisions si tu comprends l' anglais ... http://www.fixyourownprinter.com/forums/printer/66821
Cordialement ,
fanaudi .