20 Most Recent Moultrie GameSpy 4.0 Digital Camera Deluxe - Page 9 Questions & Answers

make sure card lock switch is forward toward contact strips fully.

I have read through the manual and could not find any special action required the register the change.

The only thing that I can think of is, did you continue to press the "select" button until you have left the time set routine? If you do not exit the routine then it seems likely that changes will not be recorded.

DON'T WORRY ABOUT IT...IT'S NOT SUPPOSED TO BE HOOKED UP....ANTENNA FOR REMOTE CONTROL OPTION

I'll bet the lcd is same as for D-40,M-40,M-60,I-40,I-60,ECT.
email moultriefeeders.com and tell them you have a gamecam with a defective lcd and could they please send you a replacement...they will at no charge to you, even free shipping...with instructions...this is a known issue with MANY Moultrie models

Hi,

You can download the required manual by clicking the link below:
http://images.ebsco.com/pob/Moultrie/catalog/DGS-200Instructions.pdf

You'll require Adobe PDF Reader installed on your PC to view this manual. If it is not already installed on your PC, download it free from: http://get.adobe.com/reader/

Hope this solves your problem. Thanks.

this has to be a D-40;check that push button is actually contacting push switch on printed-circuit card below..ck connections at that area of pcb...a bad solder job will ruin your day.

Hi, Sue,
Not really sure on this, but if where he bought cam will take it back,try it...
However, it may not be the cam, but different resolution settings on the two different cams. Digital cams by different manufacturers format SD cards using different means; some allow more memory space on card for formatting than others..and if the game cam is set at a higher resolution than the other cam, then the 2nd cam might use space 1st cam left avail.i.e., say cam "sets aside 4mb of memory to format card, but only uses 2mb of this space. Now, the game cam is set for high resolution and take 130 pics @ 15mb each..15x130=1950mb,+ 2mb left by game cam=1952mb(1.952gb), or about 50mb of space left on card...put it into cam set for lower res. and might get several more pics before card was really full...be sure all is equal...both cams, and card,ect. 128-130 pics @ high resolution ain't bad....on a 4gb SDHC card with my I-40's set for High Res., I can get 1000 pics;@ enhanced and I get only about 300. Set at low res., and # goes way up.Hope you understand all this.
ron

none. A # PRECEEDED BY E(event) is telling you the cam picked up, in this case, 756 events...not necessarily did it capture that many pics, but the sensor came on 756 times...had the critter stuck around past the delay setting, then you should have gotten a pic.

Here is your manual:
http://images.ebsco.com/pob/Moultrie/catalog/DGS-D40-User-Manual-compressed.pdf

..ONCE I FOUND A WIRE @ THE FLASH PCB ON A D-40 PINCHED INTO...NEVER HAD BEEN OPENED, SO MUST HAVE BEEN WHEN CAM WAS ASSEMBLED.

TRY PUSHING TO AIM...IF LASER DOESN'T COME ON, SWITCH MAY HAVE SEPARATED FROM SWITCH TOGGLE

ACTUALLY IT SAYS...ERROR 002000;FLASH TEST/FLASH CHARGING FAILED....TURN ON UNIT; REMOVE BATS; TURN UNIT OFF; REPLACE BATS; TURN UNIT ON; RUN SELF DIAGNOSTICS....HOLD FINGER OVER SENSORS WHEN MENU TELLS YOU TO.

Flash error....try removing bats with power on; turn power off; reinstall bats; turn power back on...run system diagnosis...FOLLOW SCREEN INSTUCTIONS

Sending to Moultie outside of warranty...forget it...cheaper to buy new cam...go to EBAY; you'll be bidding against me for "as is" cams....check & make sure ALL O-RINGS ARE PROPERLY INSTALLED

Don't worry about the white wire. This is the antenna for the optional remote control...if you push the "find" button on the remote, if you have that option, the green status light flashes repeatedly. Press the other button, if it's in remote, and it'll take a pic.

Moultrie knows...they will send new one; no charge
www.moultriefeeders.com

A known issue....contact moultrie (www.moultiefeeders.com)...they will send you new one free of charge; free shipping

make sure the on-off-aim switch is snapped onto the arm of the swich on the PCB

Depends on the parts...An operator (user) manual can be download/printed (PDF) from www.moultriefeeders.com