20 Most Recent
Jacuzzi Signa 6 Whirlpool JAC-B540... - Page 12 Questions & Answers
Jacuzzi hot tub will not reach temp pumps do run?
If your hot tub is running but NOT heating then you need to look at a couple of things.First, on the topside, is the heat indicator light on?If it is on and the tub is not heating then the temp sensor or the high limit sensor is not working and need to be replaced.US Parts Center
11/15/2013 5:17:18 PM •
Jacuzzi Home
•
Answered
on Nov 15, 2013
I have a jetted tub that the air switch does not
This actually sounds like you have some calcium built up on the inside of the air button.Take the trim ring off the air button and pull out the center button.Get some soft emery cloth and run it around the outside of the center button and well as the inside of the button body then reinstall. That should solve your problem with a sticking air button.US Parts Center
11/15/2013 5:01:09 PM •
Jacuzzi Home
•
Answered
on Nov 15, 2013
One of the jet assemblies
once a jet face has fallen out of a hot tub that means the insert has failed and is broken. you will need to locate a new jet insert. Jet inserts have little tabs on them that hold them in place and when they get worn out the jet face will fall out into the tub.
11/15/2013 2:21:30 PM •
Jacuzzi Home
•
Answered
on Nov 15, 2013
Burning smell
get it checked by electrician. there has to be an access panel.
10/11/2013 4:16:10 PM •
Jacuzzi Home
•
Answered
on Oct 11, 2013
I have a jacuzzi J-300
Is it bad to run it like that ? I've cleaned everything out and reset it and it still comes on?
9/28/2013 8:03:08 PM •
Jacuzzi Home
•
Answered
on Sep 28, 2013
Power button pushs in and doesn't start
If you press the air button in and it does not turn the pump on you need to check a couple things.
- Is the circuit breaker on
- is the hose still attached to the bottom of the air button and the air switch on the pump
- check the air switch in the motor - it probably needs to be changed.
US Parts Center
9/4/2013 5:58:37 PM •
Jacuzzi Home
•
Answered
on Sep 04, 2013
I have a leak where The air switch is. The leak is
The Air Tubing presses onto the little nipple on the underside of the air button. There is no seal on this set up. Once the air hose is attached to the nipple there should no air leakage when the air button is pressed.Before you install the air hose you might cut off half inch on the end to make sure the end has not splits and you get a good piece of hose so it will seal properly.US Parts Center
9/4/2013 5:54:40 PM •
Jacuzzi Home
•
Answered
on Sep 04, 2013
I have a old Jacuzzi that is leaking. on the tub
Take the unit off of the tub and see if there is a seal there,if there is a seal there try putting some silicone caulking around the seal or where the seal would be and then put the unit back together but don't over tighten the unit until the caulking is cured(24hrs) and then tighten the unit back up and this should seal it back up,unless the water is leaking past the actual switch itself,then you will need to replace this switch!Good Luck!!
9/4/2013 2:30:41 PM •
Jacuzzi Home
•
Answered
on Sep 04, 2013
Breaker trips on startup
If your circuit breaker is tripping when you turn the pump on it is caused by a bad motor. The motor probably has a short in it causing the breaker to trip,Replace your pump and that should solve your problem with the breaker.There is an outside chance you may have a bad circuit breaker too.US Parts Center
9/4/2013 5:07:32 AM •
Jacuzzi Home
•
Answered
on Sep 04, 2013
Not finding what you are looking for?