20 Most Recent Jacuzzi Signa 6 Whirlpool JAC-B540... - Page 10 Questions & Answers


Air Switch Repair
It sounds like you have a bad air switch located in your motor.
The air switch is what the air hose connects to on the back of the motor or on the box on top of the motor. The other end of the air hose is connected to the air button on the lip of the tub.
This is a latching air switch and when you push the air button it latches to send power to the motor. When the air button is pushed again it opens the latch in the air switch and stops power going to the motor shutting it off.

US Parts Center

Jacuzzi Home | Answered on Jun 06, 2014


The knobs on the jacuzzi whirlpool pull off.

US Parts Center

Jacuzzi Home | Answered on Jun 06, 2014


Air Switch Repair
It sounds like you have a bad air switch located in your motor.
The air switch is what the air hose connects to on the back of the motor or on the box on top of the motor. The other end of the air hose is connected to the air button on the lip of the tub.
This is a latching air switch and when you push the air button it latches to send power to the motor. When the air button is pushed again it opens the latch in the air switch and stops power going to the motor shutting it off.

US Parts Center

Jacuzzi Home | Answered on Jun 06, 2014


On most bath fixtures the knobs or handles are held on by a discreet screw set screw. If there is a plastic or rubber "button" in the center of the knob, gently pry it from the edges to remove it and there should be a machine screw going through the knob holding it to the valve stem. Remove the screw and the knob should come off. Sometimes requires some light tapping from the back side. If this doesn't appear to be the case, examine the back side of the knob to see if there is a set screw in a small hole going in sideways effectively clamping the knob to the stem. Often times this type will require a very small Allen wrench. Be sure to use the correct size or you will strip out the hex shaped opening and then will require drilling out. This is not what you want to be doing!

Jacuzzi Home | Answered on May 30, 2014


Jacuzzi Cetra Comfort Bath home page:

http://www.jacuzzi.com/baths/options/models/cetra

Installation and Operating Instructions:

http://www.jacuzzi.com/admin/files/files/4cfd8269-e7b0-4286-9908-7b9743.pdf

For replacement parts your best bet is to you use the on-line dealer locator:

http://www.jacuzzi.com/baths/pages/dealer-locator

or you can shop on-line from one of their authorized retailers; however did not see any of the parts you are looking for at the sites I checked:

http://www.jacuzzi.com/baths/pages/buy-online


Jacuzzi Home | Answered on May 28, 2014


Jacuzzi has the manuals online if this is a jacuzzi brand hot tub.
http://www.jacuzzihottubs.com/request-brochure/download-manuals.html

Jacuzzi Home | Answered on May 17, 2014


Bath Panels can be very difficult to locate. I would check with your local Jacuzzi Showroom first.
If they are unable to locate the panels you need or they are no longer made then you should head over to Lowes or Home Depot to get a generic panel from one of them and you may need both panels replaced so they match.

rod
US parts Center
Bath Spa Replacement Parts Hot Tub Bath Parts Accessories US Parts...

Jacuzzi Home | Answered on May 13, 2014


This unit has to go inside preferably a bathroom setting. The wall fixtures on the rear of the unit are proof enough of that. A plumber will need to install the unit as some bathroom plumbing will be required.

Jacuzzi Home | Answered on Apr 29, 2014


Your problem is most likely NOT the air button but the switch in the motor.
Air Switch Repair
It sounds like you have a bad air switch located in your motor.
The air switch is what the air hose connects to on the back of the motor or on the box on top of the motor. The other end of the air hose is connected to the air button on the lip of the tub.
This is a latching air switch and when you push the air button it latches to send power to the motor. When the air button is pushed again it opens the latch in the air switch and stops power going to the motor shutting it off.

Rod
US Parts Center

Jacuzzi Home | Answered on Apr 13, 2014


The 'low-water' sensor installed in a bathtub is designed to NOT allow the pump to run without water contacting it.
It sounds as if this is operating as it should.
Once the pump comes on you should be able to touch the "logo" or the on/off button to turn the pump on and off.
If the pump is not turning on/off when the tub is full of water you may be experiencing a problem with the control box under the tub skirt.

Rod
US Parts Center
888-521-6183

Jacuzzi Home | Answered on Apr 08, 2014

Not finding what you are looking for?
Jacuzzi Signa 6 Whirlpool  JAC-B540... Logo

Popular Tags

22 questions posted

Ask a Question

Usually answered in minutes!

Top Jacuzzi Home Experts

Mike

Level 3 Expert

4369 Answers

john h

Level 3 Expert

23424 Answers

Bill Johnson

Level 2 Expert

306 Answers

Are you a Jacuzzi Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Jacuzzi Home

  • Jacuzzi Home

Most Popular Question

jacuzzi hot tub model j 300 series fl 1

  • Home
Loading...