Black & Decker PI400AB Power Inverter - Answered Questions & Fixed issues


test the battery if it is still OK

Black & Decker... | Answered on Oct 27, 2012 | 821 views


If it is the fuse inside the cigarette lighter plug, just unscrew it and put a new fuse in.

If you mean replacing the two 25amp fuses inside the inverter housing, you can bypass the fuses by soldering the two sides together. Or, if you want to put new fuses in, heat the solder holding the fuses in until they pop out and insert new ones.

As for opening the housing, good luck!! I ended up using steel cutters to rip off the plastic. The best option would be to buy a new one and return the old one in the package.

Black & Decker... | Answered on Apr 11, 2011 | 1,439 views


Rather than try to repair it or look inot it, call the dealer or take it back to him as you will invalidate your warranty and that is not worth it. Let the dealer worry about it.

Black & Decker... | Answered on Mar 04, 2011 | 337 views


over loading unit triping braker ......why?/interanel short?

Black & Decker... | Answered on Dec 26, 2010 | 279 views


I've had this inverter for about two years now, bought it for a cross country road trip to power my laptop and a couple of other things. I've pretty much liked it. Yes, the fan is a little noisey, yes, you have to use the provided battery clips for heavy loads. But it powers my Dell Inspiron 8500 laptop just fine (and its an old powerhog).

Recently a I let a friend use it with his inflatable mattress air pump during a camping trip.
What I didn't know is his pump has insane wattage, and it fried/bricked the inverter instantly.

Agh! I thought it was a goner, but took the time to look inside the unit. (Which is a solid and sturdy metal case, not plastic as another reviewer indicated). I was thrilled to discover there were some internal fuses. And while the fuses are soldered to the circuit board, if you've done any soldering at all they really are a snap to replace.

If you remove the four screws that hold the end cover plate on the side with the fan. You can remove the end plate and have just about a half inch or so of clearance. The entire lower circuit board will then slide out with firm pressure about an inch and a half (don't try and go any further, components on the other side prevent it).

On the right side (positive/red terminal side), you will see two 25 amp mini-fuses that are directly soldered to the circuit board. If these are blown (you can see through the semi-transparent sides if they still connect), that is most likely your problem. They are easily available from most auto and big department stores (Walmart, Target, etc) in their automotive sections.

I used a 40 watt soldering iron (30 watt should work fine), and applied it to the bottom of the circuit board where the fuse legs poke out the bottom. Using a pair of pliers, I applied a firm steady pressure to the fuse, pulling up, while applying the soldering iron to each of the legs (alternately) of the fuse. The solder melted, and I was able to work the fuse out in a few seconds. I did this for both fuses.

The replacement fuses cost all of $2. I dipped the new fuse legs in flux, then put them in the place of the old fuses. Again I heated the circuit board solder from below, and pushed the new fuse in place. Repeat with the second fuse until it is in place. Flip the board over and add some more new solder until it is firmly in place. Put it back together, and you are back in business! And for a whole lot less than a new inverter.

I've got pics of this process if anyone would like them. Good luck, and happy inverting.

Black & Decker... | Answered on Jun 20, 2014 | 1,462 views


40 A  

Black & Decker... | Answered on Jun 14, 2010 | 463 views


Are you referring to an inverter by a "power box"? That term doesn't really describe the device. I'm going to assume it's an inverter you're talking about, a device that takes DC and turns it into AC. I'm not sure about that, but you should be able to plug a converter (turns AC into DC) of the right voltage, 12 to 14 volts DC into a generator on the boat and run it. I'm assuming the trolling motor runs off 12 volts DC and NOT gasoline. Be sure to check that before doing anything. Most do run off a large car or RV battery. Lead Acid Batteries for boats and cars produce 12.7 volts DC if they are in good shape and should have six cells (about 2volts per cell). 6 volt batteries are somewhat rare these days and have 3 two volt cells. Two of them in series will also power it.
Thanks for asking that question ... I like to fish also.

Lynn

Black & Decker... | Answered on Mar 22, 2010 | 190 views


I can't answer your question but I strongly suggest you urgently contact the manufacturer or dealer in order to clarify this most important point as a 3kw inverter isn't cheap and shouldn't need replacing very often.

Black & Decker... | Answered on Aug 31, 2017 | 1,275 views


Sure, you can find it on amazon... here: Amazon com Husky jump start adapter . I hope I have helped. Cheers

Black & Decker... | Answered on Dec 01, 2014 | 2,047 views


well the yellow light indicates a fault, the 5 volt USB is independent of the invert-er function, you kneed your unit serviced or possibly you have a low voltage cutout or high voltage protect ,check you manual for led fault indicator descriptions, battery voltages should be between 10.9 volts and 13.8 volts this can cause a fault if outside this range.
best regards Falco

Black & Decker... | Answered on Nov 05, 2013 | 271 views


Most power inverters supply a modified sine wave output. This is different from the true sine wave you get at home. It's close enough for many applications, but not close enough for many transformers, which is what your laptop power supply is. So the problem is that your laptop's power supply does not work with a modified sine wave input. Some will, some won't. Very common problem.

Black & Decker... | Answered on Aug 23, 2010 | 303 views


Look on this site and see if yoou can find one with:

Correct dimensions
Correct voltage
Correct terminal connections

Don't worry if capacity is a few more amp hours. Some batteries have improved the capacity.

Use your measuring tape for size.

http://search.digikey.com/scripts/DkSearch/dksus.dll?Cat=393246&k=battery%20sealed

Black & Decker... | Answered on Oct 23, 2009 | 1,335 views


sounds like my inverter im going to change the mofset or.triod it has 3 prongs.

Black & Decker... | Answered on Jul 27, 2009 | 218 views


Purportedly pressing enter clears the error message. https://www.manualslib.com/manual/1293218/Keb-Combivert-F5.html?page=55#manual
The error means the "power circuit is not ready" according to the error code page. http://www.servotechnica.spb.ru/viewdocument/KEB_CD/manuals/f5/f5s/00f5subk250.pdf?page=33

The following page has the contact details for the company in the US as the last listing. http://www.servotechnica.spb.ru/viewdocument/KEB_CD/manuals/f5/f5s/00f5subk250.pdf?page=33

Electronics -... | Answered on Jan 19, 2021 | 11 views


The EKO 5000DB inverter is purportedly a rebranded 5KW Solis Ginlong inverter. Here is a YouTube regarding steps to take if an OV bus error message is encountered.

https://www.youtube.com/watch?reload=9&v=Ghja5q7palE

Additionally, a link to a Ginlong manual with a troubleshooting section follows:

https://www.manualslib.com/manual/1389769/Ginlong-Solis-6k.html

Current Solis manuals may be downloaded from: https://www.ginlong.com/rhi_inverter1/1952.html

Electronics -... | Answered on Jan 19, 2021 | 496 views


You will have to buy a new ac adapter.

Electronics -... | Answered on Jan 11, 2021 | 169 views


You did not post any information on the make and model of the card reader. This is something that we need to know. You need to check the cables to reader and the server the reader is on.

Electronics -... | Answered on Jan 01, 2021 | 192 views

Not finding what you are looking for?
Black & Decker PI400AB Power Inverter Logo

18 questions posted

Ask a Question

Usually answered in minutes!

Top Black & Decker Electronics - Others Experts

Cindy Wells

Level 3 Expert

6222 Answers

Sheldon Dedek

Level 3 Expert

912 Answers

Vernon Taylor

Level 3 Expert

7437 Answers

Are you a Black & Decker Electronics - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...