20 Most Recent Dewalt DW411 quarter - sheet palm grip sander with dust collection - Page 5 Questions & Answers

Dewalt 735 planer wont start

Power? circuit breaker? Plug? Owner's manual. Troubleshooting
Does the motor hum? if so you have something jamed in the planer cutter.

Dewalt Tools &... | Answered on Feb 28, 2015

1 Answer

My Dewalt d26541 orbital sander, which I have had for 4 years, stopped running. Could the brushes cause this or is the motor shot?

Brushes can definitely cause this but unless you feel fairly confident in pulling the unit apart, it may be more cost effective to just replace it. It would be unusual to see the brushes wear out so quickly but I do not know how much you use it or the load you put it under. I have a Rigid that I use a LOT and have had it for probably 5 - 6 years and it is holding strong. These things just tend to last. I would contact DeWalt and see if you can have them send you new brushes first and then go for it; the worst is that you ultimately have to replace it (which you might have had to anyway) and the upshot is that you fixed it yourself and now have many more years and sawdust sneezes in your future.

Dewalt Tools &... | Answered on Feb 14, 2015

2 Answers

My cordless Dewalt finishing gun has stopped firing when you try to fire it in a vertical position. Works fine on skirting and architrave but just gives a little 'pop' if try to fix anything to ceilin

is this a gas cartridge type of nailer? It could be the effects of gravity on the spray nozzle. try pushing down in normal position but dont fire it. quickly move to ceiling then try firing. I am not a fan of this type of nailer as they are problematic and finicky.

Dewalt Tools &... | Answered on Feb 11, 2015

1 Answer

How do i change blades in my Dewalt dw733 surface planer?

There a Youtube video on how to do this

https://www.youtube.com/watch?v=8qDwehIi8CU

Dewalt Tools &... | Answered on Feb 09, 2015

1 Answer

How do I restart my dewalt dw733 thickness planer

I think you have to call the service center on this one,
http://www.dewalt.com/Find-Service-Center.aspx

Dewalt Tools &... | Answered on Feb 09, 2015

1 Answer

How can I find an owners manual for a DeWalt D51256 nail gun?

5-10 drops directly in the air fitting before each use.

Dewalt Tools &... | Answered on Feb 07, 2015

0 Answers

My dewalt orbital sander turns on but when I apply it to a surface it shuts off dies not spin ?

Dewalt Tools &... | Posted on Feb 06, 2015 | Be the first to answer

1 Answer

How do I change the brushes on a 14" dewalt impact wrench 14.4 volt

I think that model is on a ring internally so there isnt a way to do like the bigger ones, you would have to take the screws out and take in half and you will the the brushes and can replace.

Dewalt Tools &... | Answered on Jan 12, 2015

1 Answer

Dewalt 771 slips in all torque settings in low, but works in high setting

The clutch is defective , you can get replacement parts from dewalt. There are several dewalt service centers in the US

Dewalt Tools &... | Answered on Jan 07, 2015

1 Answer

How do I do the Dew?

To do the dew one must see the dew and then become the dew.

Dewalt Tools &... | Answered on Dec 30, 2014

1 Answer

How do I take apart a drill chuck dewalt dc759

why would you want to take it a part?

Dewalt Tools &... | Answered on Dec 07, 2014

1 Answer

Dewalt dw625e intermittent power fault

Some power tools have a thermal reset switch built in. It sounds as if the thermal overload is faulty, or the unit has overheated. Check to insure the cooling ports of the motor are not clogged with sawdust.

Dewalt Tools &... | Answered on Oct 19, 2014

1 Answer