20 Most Recent Pride Revo 4 Wheel Scooter - Page 9 Questions & Answers

Hello, Dennis -Only the manufacturer of the scooter, Pride Mobility, will know what year that scooter was manufactured. This is the toll free phone number for Pride Mobility Customer Service: 800-800-4258. Their hours for taking calls Monday - Friday, 8:30 am - 5:00 pm, Eastern Time zone.Best wishes.

Hi check the wheel bearing ..cheers

Hi again try this remove key & push freewheel lever into freewheel then push it into drive put key back & hope the control box has reset...PLUS CHECK THE BATTERIES WITH A LOAD TESTER available on E/Bay cost aprox $35 dollars .. flash code ( CURRENT LIMIT TIME OUT ) TURN SCOOTER OFF FOR A FEW MINUTES THEN TURN IT BACK ON ... cheers

Here is a link to a webpage with the diagrams/schematics. Click on the diagram to make it larger. They seem to have most of the diagrams of this mobility scooter well covered. Sc3450 Replacement Parts S6324704016c30 And Prior Electronics Assembly...

faulty voltmeter and /or bad batteries have the batteries load tested to eliminate them then replace the voltmeter in reality it should be showing a reduction in volts available as the batteries run down form use as an example fully charged batteries 12 or 13 volts go for a trip around the block and as you go the meter should start reading a lesser voltage as you are going or a reduced voltage at each stop

Hi it's possible the control box down timer was activated check if freewheel lever is in drive remove key & wait a few minutes replace key & turn on cheers.

Hi 7 beeps is a speed pot error . Cheers

Hi u have to replace it if it is faulty / remove it & check it's resistance in ( ohm's ) with a multimeter.. Cheers

The error code suggests a problem with the power module motor 1 output to the brake or a problem with the motor 1 brake. You can swap the motor leads to see whether the problem is in the module or brake.

I would inquire at the link below as they supply replacement parts for the Pride MAXIMA scooter. Pride Mobility OEM Replacement Parts How to Repair Pride Mobility Scooter Pride Mobility scooter Owner Manual

1. VR2/VSI DIAGNOSTIC FLASH CODES

# OF LEDS CODE CAUSE POSSIBLE SOLUTION One red LED 1 Low battery voltage Charge batteries Two red LEDs 2 Left motor open Make sure left motor is plugged into controller. Three red LEDs 3 Left motor wiring fault Contact your authorized Pride Provider. Three red LEDs One yellow LED 4 Right motor open Make sure right motor is plugged into controller. Three red LEDs Two yellow LEDs 5 Right motor wiring fault Contact your authorized Pride Provider. Three red LEDs Three yellow LEDs 6 Inhibit active Contact your authorized Pride Provider. Three red LEDs Four yellow LEDs 7 Joystick error Contact your authorized Pride Provider. Three red LEDs Four yellow LEDs One green LED 8 Controller error Contact your authorized Pride Provider. Three red LEDs Four yellow LEDs Two green LEDs 9 Brake fault Make sure both motors are plugged into controller. Three red LEDs Four yellow LEDs Three green LEDs 10 High battery voltage Contact your authorized Pride Provider. What if the speed LEDs on the VR2/VSI begin to flash?

• Determine if the battery charger is connected to the power base. When the battery charger is connected to the power base, a charger inhibit feature keeps the power chair from driving. This is indicated by the VR2/VSI speed LED(s) flashing.
• Determine if the charger harness fuse has blown. A blown charger fuse can cause the charger inhibit to activate.
• Determine if all controller connections are plugged into the power base properly. If the 3-pin charger inhibit connector is not plugged in properly, then the charger inhibit feature will activate.

it may need new seals, they get crapped up with oxidation, this stops the piston retracting and they bind on.

If you're having trouble with that controller, there are repair centers for them. Repairs are much cheaper than buying a new one. https://www.pridemobility.com/.../GC3_Controller_BOI.pdf This may help with troubleshooting.

You can get a replacement switch from Prides web site.

The brakes need adjusting or replaced

Service the magnet brake assembly on each motor.

https://www.pridemobility.com/.../US_Jazzy/US_Jazzy_1170_om.pdf Look on page 16. There's where the circuit breaker is located.

You can get then from Prides website

You can get this information from Pride's website

You van get diagrams from the Pride website.