20 Most Recent Achiever CCS5000 Shredder Questions & Answers


We are going to purchase a new shredder. Changing the fuse did not work.

Achiever CCS5000... | Answered on Dec 07, 2016


possibly thru the manufacturer but many do not offer replacement gears .

Achiever CCS5000... | Answered on Oct 19, 2016


I replaced mine with a 4 amp 250 volt 5mm dia. x 20mm long Slow Blow Glass Fuse - equivalent to what i took out.

Achiever CCS5000... | Answered on Aug 29, 2016


I could take a photo of the belt layout on my unit for you and paste it here. I'm still looking for help with the paper sensor on mine, which seems dead. I'm not sure how it is supposed to work, but it looks like perhaps it's a photo diode and a sensor that might trigger the relay when paper interrupts the light path. I can see two pairs of wires leading to something on each side of the paper path. Any ideas how it works?

Achiever CCS5000... | Answered on Apr 05, 2016


These are the guys who should help; http://www.worldofficeproducts.net/contact.html try them first for troubleshooting and spares and dealer locations. they don't have anything online with any details more than sales literature. Hope this helps - please ask again if no luck :)

Achiever CCS5000... | Answered on Aug 04, 2015


unplug it & flip it upside down. there are 4 bolts,1 in each corner. remove them & turn it back right side up & carefully pull the top off. there will be a few wires attaching the board in the top to the bottom 2 of them should have quick connects that you can remove. now you should be able to see what is caught. if you can't get it out without powering up, hook the 2 quick connects back together & turn it on with the switch. by rocking it back & forth it should be able to come out. a pair of needlenose pliers might help & keep fingers out of machine. hope this helps ya. i love this shredder

Achiever CCS5000... | Answered on Feb 18, 2015


I had the same problem. I super-glued the pieces togeter and allowed them to dry completely (over night). Then I super-glued two strips of plastic perpendicular to the original brake and allowed to dry completely. It has worked for several years without difficulty. I was unable to find the broken part. However, if I had a plastic injection moulder, I would make them and sell them for $20 each; free postage.
Good Luck
David

Achiever CCS5000... | Answered on Dec 10, 2014


Shredders have a manual switch for reverse..... if you have tried this, then there could be a possibility that the switch has dust of paper in it and the contacts not making contact for the reverse cycle... or the switch is faulty. If you have any electrical knowledge, you can do a test with an ohm meter for continuity in the reverse mode.... or remove the switch and blow it out with an air compressor. If you mess with electrical, ALWAYS REMEMBER TO UNPLUG THE SHREDDER!!!
Good luck.........

Achiever CCS5000... | Answered on Jul 15, 2014


you dont give much explaination of what it looks like ....I have fixed several of these shredder problems like this.. I had the same problem, but I formed one with JB Weld. I put on a layer, let it dry (24 hrs) and then added another layer... I did this five times. to get it high enough to touch the switch.
Do you have the piece that broke off? Use JB weld to glue it back... JB weld hardens to the strength of steel...
If you dont have the piece, use your imagination and improvise one made of plastic or metal... then JB Weld it, But make sure you have the correct length by using a small ruler to insert to where the switch is activated. MEASURE TWO OR THREE TIMES... AND CUT AND GLUE ONCE. PAY ATTENTION TO THESE LAST TWO LINES.

Achiever CCS5000... | Answered on Mar 01, 2014


Do a very thorough inspection of the cutting blades. I have found that just a shred of paper, that one would think would not be a problem, can in fact make your shredder act as you describe. How old is it? Depending on age & the heavy usage you say it has had.... it could very well be good old made in USA obsolescence. Wish I could tell you more. Without a multi-meter;(Ohm Meter). & manual to know what power is getting from point A to point B I cannot advise beyond this. Sorry.

Achiever CCS5000... | Answered on Dec 25, 2013


the overload beeper want cut off and there no paper in it

Achiever CCS5000... | Answered on Oct 10, 2013

Not finding what you are looking for?
Achiever CCS5000 Shredder Logo

86 questions posted

Ask a Question

Usually answered in minutes!

Top Achiever Office Equipment & Supplies Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

quennie732

Level 2 Expert

422 Answers

Cosmas Matanda
Cosmas Matanda

Level 2 Expert

67 Answers

Are you an Achiever Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Achiever Office Equipment & Supplies

  • Achiever Office Equipment & Supplies

Most Popular Question

need know re wire ccs5000 rocker switch

  • Office Equipment & Supplies
Loading...