Garmin eTrex Venture HC GPS Receiver - Answered Questions & Fixed issues
Garmin troubleshooting
replace it or try a master reset. that is an old unit.
https://support.garmin.com/support/searchSupport/case.faces?caseId={dc0a1390-14a9-11de-76c5-000000000000}
8/9/2014 4:26:35 AM •
Garmin eTrex...
•
Answered
on Aug 09, 2014
•
215 views
My GPS won't stay on
I can solve this by not solving it. First I tried reset the unit to default settings: hold down the power, page, and enter buttons at the same time, a message, "do you really wan to reset..." will appear. Select "yes." If the unit reboots, hurrah. If not, call tech support (1.800.800.1020). Get an RMA, send it back to them for repair. I had purchased mine over 30 days ago but less than 60: Amazon wouldn't replace it, Garmin will either replace or repair. If you want them to send a new unit while the old is in transit, just ask; they will charge and then credit a card once they have the old unit is in hand. Good luck.
3/15/2010 8:53:52 AM •
Garmin eTrex...
•
Answered
on Mar 15, 2010
•
5,205 views
How do I calibrate my compass in the eTrex Venture
I will be happy to help you with this. Unfortunnately, the Etrex Venture does not have an Electronic Compass, therefore you cannot calibrate it. What this means is that this unit will show the correct direction of travel as long as you are moving. The unit takes satellite reading every 1 seconds and compares it's location with the last location. This way it can read the direction of travel. It will not give correct readings unless you are moving.
I hope this helps.
12/31/2009 5:01:11 AM •
Garmin eTrex...
•
Answered
on Dec 31, 2009
•
809 views
My etrex Venture HC will not power up after
I can only suggest that you insure that you have fresh batteries, and that they are installed properly. If you had batteries sitting in it, and they leaked, you might want to examine the contacts and make sure they are clean, and not corroded.
The Etrex are sealed and water-tight. Opening the unit will make them no longer able to resist water as well, and if there is anything wrong internally, it should be sent back for factory repair.
11/6/2009 11:43:36 PM •
Garmin eTrex...
•
Answered
on Nov 06, 2009
•
615 views
Cant find how to manually input cordinates
First create a waypoint, and then modify it. Hold down the enter button for two seconds (the thumb-toggle on the face of the unit). This opens a screen with a number at the top and coordinates of your current location below. Once you've grabbed the coordinates you can change the name and the coordinates and the name and save it as a waypoint. Use the thumb-toggle to bring up number pads and letter pads for each line.
5/25/2009 2:20:09 PM •
Garmin eTrex...
•
Answered
on May 25, 2009
•
496 views
How to prevent Drive52 continually resetting itself ?
By 'resetting' you mean it switches off, and because it is connected to power, it boots back up. Do you have a SD Card in it?
I had trouble with a Nuvi 1350 with SD Card that had the whole USA Map on it, mine came with the Canada Map only. It would randomly turn off, so I decided to buy a Factory Refurbished Drive 50. I removed the SD Card and Reset the Nuvi and it worked perfectly after that.
The Drive 50 was also a bit flaky, and resetting fixed that as well.
You can back up your Favourites beforehand.
7/21/2023 1:33:43 AM •
Garmin GPS
•
Answered
on Jul 21, 2023
•
40 views
I have the Garmin etrex 20x and wish to calibrate the compass
I recently purchased a Garmin GPSMAP 78s
I had a lot of trouble calibrating the compass; I literally tried it hundreds of times without success. I also did a hard reset etc etc. Believe me I definitely tried everything possible but to no avail
I did contact Garmin but they didn't have an answer straight away for the problem
I have now sorted it as follows:
Do each step VERY SLOWLY, MUCH slower than you think you should
There are three steps to go through in calibrating the compass 1)Spinning the whole unit around flat 2)Flipping it over longitudinally and then 3) Flipping it over end to end. But remember do each step VERY slowly and go to the next step when prompted by the unit
This solved my issue. I can now calibrate my compass 9 out of 10 attempts
Hope that helps
7/16/2023 11:59:56 PM •
Garmin GPS
•
Answered
on Jul 16, 2023
•
464 views
Not finding what you are looking for?