Sharp MX-2700N Color Copier - Page 6 - Answered Questions & Fixed issues

In the printing properties, on the paper select tab, change the paper tray from automatic to by pass tray

Some possibilities are:

1) Dirt on the glass, dirt on the glass strip for the doc feeder, or dust on the mirrors. This would be the case if the line only showed when copying and not printing.

2) Toner dropped onto the charge sawtooth.
This may be possible if the line is intermittent and only showed up for 1 or 2 colors.
Open the front door and remove the waste toner box. To the left of each drum there is a green organ-stop type stem. Pull and reinsert each stem. You will hear a zipping noise. These are your charge scrubbers.
This may be not as likely if the line shows up in the same place on all 4 colors

3) Toner or dust on the lens
This may be possible if the line is intermittent and only showed up for 1 or 2 colors.
In the area where the waste toner box goes, look for a grey stick with a white cushion on the end. This is your lens scrubber. Look in the area under the charge scrubber on each drum cartridge for a gap. Insert the scrubber cushion side down into the gap and run it forward and back to clean the lens.
This may be not as likely if the line shows up in the same place on all 4 colors

4) Transfer belt blade not cleaning
This is best handled by a service tech since the mylar belt is very fragile. The squeegee blade that cleans the transfer belt between copies is missing a spot. The blade needs to be taken off the belt, cleaned and repowdered. Recently, Sharp made changes to the composition and thickness of the mylar in the transfer belts. Overpowdering the blade or belt when it was changed may cause improper cleaning of the belt creating lines across the copies. Often the condition clears up after a couple of days as the gap between the blade and belt is sealed.
This is most likely the cause as the line shows up in the same area for more than 1 color.

5) Transfer belt and/or blade is worn out
If the belt is worn the blade must be replaced but not vice versa.

6) Clogged waste augers in the drum cartridges.
Waste toner may cake up in the drum cartridge and knock loose on the drum.

It may be time for full maintenance on the machine.

Before printing click the property button, go to papar tab, under tray select, change from auto select to by pass tray

fuser count has reached 200,000 copies. hit P*C* then 24, start, then 4 start. select Fuser Unit and Fuser Acum Day then execute at bottom then yes. Hit CA button. copier should reboot and clear code.

this copier has many size options but if you try to run a differnt size it may tell you to add a differant paper size, try using the( extra) size in your bypass or use a standerd size paper bigger than what you want and cut it down

Hi
be very careful you could cost your self allot of $

If the grey band moves it could be 1 of 2 things 1st try cleaning the fuser section be careful it is very hot, and if you not familiar with this you may want to find a service provider, it can get a little tricky, 2nd it could be the Drum cleaning blade and the drum need to be replaced. if you take the drum out this also can be very tricky. It sounds also like it may just need to be cleaned like the mirrors and platen.

Good Luck

i think that u2 shows some memory or eeprom problem just reset it .press clear key,exposure mode key,clear key,exposure mode key,press all these key in sequence and quickly.display will go dead now press 16 then start key.code will bi removed .mian jee

Use SIM14 to
cancel the trouble.

Entering the simulation mode
1) Copy mode key ON → Program key ON → Asterisk (*) key
ON → CLEAR key ON → Asterisk (*) key ON → Ready for input of a main code of simulation
enter 14
accpet yes clear..
machine should restart.
You may have to have a tech look into why this is jamming...

Hope that helps
Lbcoaster

Type in p * c * then 14 press copy key then CA. Machine will reboot, if problem is still there after reboot, one of the thermostats in the fuser has tripped. Did this happen soon after a jam?

P * C * enter sim 14 press copy key then CA. Machine should reboot. if problem re-occurs your thermostat in the fuser has tripped

https://www.fixya.com/support/t14696300-reset_change_counter_sharp_ar_5726

Question edited for clarity, turned around, added CAPS, added the word 'manual'.Duplicate question should have been deleted but Kardoc has answered, albeit wrong model. Refresh page to see your question when you press 'Post Question'.UX-105 in Russian, or 510 in English, which is probably close enough.https://www.google.com/search?q=sharp+ux-105+manual..

https://www.manualslib.com/products/Sharp-Ux-510-641495.html

Question edited for clarity. Remove the curl out of the paper by running 6" across the edge of a desk against the curl. With scissors, cut the end 1/2" straight. Then cut a 1/2" off both corners at 45 degrees. Push the paper in the slot and press the Feed Button. https://www.google.com/search?q=Sharp+EL-1197PIII.+How+to+load+paper My instructions are better than the video, but shows the process well. ..

Hello, Just replace toner cartridge or refill the toner container with refillable sharp ar202 refill bottle or sachet. Remember to remove waste toner if you are refilling, right.

Error Codes > Sharp > MXC300W > Code L4-17

PrintCopy .info https://printcopy.info > brand=Sharp > code=L4-17 Code: L4-17; Description: Drum motor lock trouble; Causes: Drum motor trouble Connection trouble of the connector and the harness between MFPC PWB and the ... ..

SCIENTIFIC CALCULATOR OPERATION GUIDE

Sharp Global https://global.sharp > guidebook > documents > s... PDF Enters data for statistical calculations. Splits data used for dual-variable data input. (Used for dual-variable

Check that the ink roller hasn't moved. Make sure the paper path is clear. https://www.google.com/search?q=sharp+el-1801v+not+printing ..

1. Check the Remote: Make sure you have the remote control for the projector.
2. Press the Menu Button: On the remote, press the "Menu" button.
3. Navigate to Security or System Lock: Use the arrow keys on the remote to navigate through the menu options. Look for a section related to "Security" or "System Lock."
4. Enter the Unlock Code: If you previously set a system lock code, you will need to enter it using the remote control. If you haven't set a code before, try the default code (often 0000 or 1234).
5. Disable System Lock: Once you've entered the correct code, navigate to the option to disable or unlock the system lock.
6. Confirm: Follow the on-screen instructions to confirm your choice, and the system lock should be disabled.

Help and videos in the link https://www.google.com/search?q=sharp+ar+5620+copier+faded+print ..