20 Most Recent Sharp MX-2700N Color Copier - Page 8 Questions & Answers

enter code 20-1 start

had same issue found solution as follows

Go into port settings of printer, click configure port remove tick for 'SNMP status enabled'

Soon as we did this printer came back online

enter code 22-13 and see password

Hello.

Sounds like you need a service call. But, the tech should first check/inspect the Drum, Transfer Unit, and Fuser Unit and then reset your counter.

Hope this helps.

Press SYSTEM SETTINGS
select Admin Password and enter the password as "admin" and OK on both screens
Scroll to LIST PRINT (ADMINISTRATOR)
Select IMAGE SENDING ACTIVITY REPORT and select FAX. This will print out the log up to a maximum of 200 events ( Tx, Rx and failed sendings)
If you want a transaction report printed for each individual transmission:
Enter Admin mode as above
Got IMAGE SEND SETTINGS
FAX SETTINGS
TRANSACTION REPORT PRINT SELECT SETTINGS and select Single Sending / Broadcast etc and PRINT OUT ALL REPORT
Press OK then CA to exit

I assume you are referring to the authentication system in use on this machine. To turn it off:
Press SYSTEM SETTINGS
Touch Admin Password at top of screen
Touch the Password box and when the keyboard comes up type "admin" (case sensitive) and press OK, then OK on passord screen.
Scroll to page 2 and select USER CONTROL
Select USER AUTHENTICATION SETTING and untick the box.
Press OK then press the CA button. This should remove the password requirement.

Problem on your copier memory stick.
Solve:clean all surface with contact cleaner.
Mother Board clean with contact cleaner.Then solve your problem.if you are not fix your problem then replace memory.

The black drum unit has reached the end of it's lifespan.

Maintenance timing display The message of maintenance execution timing is displayed when each counter reaches the set value. The relationship between the messages and the counters is shown blow. Maintenance counter AA WhenThe maintenance counters (both of total and color) reaches 90% of the set value of SIM21-1 (When the setting of SIM26-38 is ?print stop?). When The maintenance counters (both of total and color) reaches the set value of SIM21-1 (When the setting of SIM26-38 is ?print allowing?). Enable ? After completion of the maintenance, execute SIM 24-4 (Maintenance counters (total, color) clear).

Hello sir; Do you see the tray 3 ,if did not see tray 3 as well, you better check the connector behind the machine, see there is connect property.

E7 is only part of the code. It could be a hard drive problem, memory problem, laser problem, or a loose connection on one of the boards.

Some possibilities are:

1) Dirt on the glass, dirt on the glass strip for the doc feeder, or dust on the mirrors. This would be the case if the line only showed when copying and not printing.

2) Toner dropped onto the charge sawtooth.
This may be possible if the line is intermittent and only showed up for 1 or 2 colors.
Open the front door and remove the waste toner box. To the left of each drum there is a green organ-stop type stem. Pull and reinsert each stem. You will hear a zipping noise. These are your charge scrubbers.
This may be not as likely if the line shows up in the same place on all 4 colors

3) Toner or dust on the lens
This may be possible if the line is intermittent and only showed up for 1 or 2 colors.
In the area where the waste toner box goes, look for a grey stick with a white cushion on the end. This is your lens scrubber. Look in the area under the charge scrubber on each drum cartridge for a gap. Insert the scrubber cushion side down into the gap and run it forward and back to clean the lens.
This may be not as likely if the line shows up in the same place on all 4 colors

4) Transfer belt blade not cleaning
This is best handled by a service tech since the mylar belt is very fragile. The squeegee blade that cleans the transfer belt between copies is missing a spot. The blade needs to be taken off the belt, cleaned and repowdered. Recently, Sharp made changes to the composition and thickness of the mylar in the transfer belts. Overpowdering the blade or belt when it was changed may cause improper cleaning of the belt creating lines across the copies. Often the condition clears up after a couple of days as the gap between the blade and belt is sealed.
This is most likely the cause as the line shows up in the same area for more than 1 color.

5) Transfer belt and/or blade is worn out
If the belt is worn the blade must be replaced but not vice versa.

6) Clogged waste augers in the drum cartridges.
Waste toner may cake up in the drum cartridge and knock loose on the drum.

It may be time for full maintenance on the machine.

Ah, the dreaded CE-00 and CE-02. This is a networking problem!!

It means the IP address stored in the copier for the computer you're trying to scan to is old and stale!!! That workstation got its IP refreshed by DHCP and your copier has been left in the dust!

To refresh the workstation's scan profile information in the copier either:
1) Reboot the workstation, or
2) Find the Network Scanner Tool icon in your tray, right-click on it, find Automatic Profile Update, and click on Update Now.

Also check the webpage and make sure that if you're using DNS for name resolution that you have the correct and working DNS IP's!!

In the printing properties, on the paper select tab, change the paper tray from automatic to by pass tray

Before printing click the property button, go to papar tab, under tray select, change from auto select to by pass tray

fuser count has reached 200,000 copies. hit P*C* then 24, start, then 4 start. select Fuser Unit and Fuser Acum Day then execute at bottom then yes. Hit CA button. copier should reboot and clear code.

this copier has many size options but if you try to run a differnt size it may tell you to add a differant paper size, try using the( extra) size in your bypass or use a standerd size paper bigger than what you want and cut it down

Hi
be very careful you could cost your self allot of $

If the grey band moves it could be 1 of 2 things 1st try cleaning the fuser section be careful it is very hot, and if you not familiar with this you may want to find a service provider, it can get a little tricky, 2nd it could be the Drum cleaning blade and the drum need to be replaced. if you take the drum out this also can be very tricky. It sounds also like it may just need to be cleaned like the mirrors and platen.

Good Luck