Top 20 LG LH-T754 Theater System Questions & Answers

Hold down "2" on the remote simultaneous to "stop" on the receiver. In a couple of seconds you will see something appear on the display. OPO-63? Anyway, repeat the process again when you see that. The system will reset. This will also take care of the inability to switch to AUX or Ipod.

Generally speaking, an amp protects itself from heat, shorts, overloads and operator exuberance by refusing to turn on or stay on.

Overloads can be from excessive periods of high output or marginally low impedance loading by the speakers; and shorts would be wiring issues or a speaker blowing up.

You should be able to feel if it's hot. WHY is it overheating? Make sure it has sufficient ventilation on all sides and that vent holes are not blocked by dust balls. Eure the fan (if equipped) is running as designed (some only operate on demand). Clean dust and debris from it.

If the amp comes back on after cooling, you're lucky. They only have so many self-protection cycles in their lives so continuously resetting or cycling their power without addressing the cause can do more harm than good.

If it protects immediately on a cool power up you should disconnect the speaker connections and try it 'naked'. If it comes up then diagnose which lead(s) are shorted. If it does not come up the problem is internal and should be left to an experienced and competent hands-on tech.

Unplug the unit for 60 minutes, when you plug it in hold the power button for 5-10 sec which will do a hard reset. This will reset the processor and hopefully the unit will operate normally.

It sounds like it isn't fully powering on or the logic is hosed up.

Generally speaking, an amp protects itself from heat, shorts and overloads.

Overloads can be from excessive periods of high output and shorts would be wiring issues or a speaker blowing up.

You should be able to feel if it's hot. WHY is it overheating? Make sure it has sufficient ventilation on all sides and that vent holes are not blocked by dust balls. Ensure the fan (if equipped) is running as designed (some only operate on demand). Clean dust and debris from it.

If the amp comes back on after cooling, you're lucky. They only have so many self-protection cycles in their lives so continuously resetting or cycling their power without addressing the cause can do more harm than good.

If it protects immediately on a cool power up you should disconnect the speaker connections and try it 'naked'. If it comes up then diagnose which lead(s) are shorted. If it does not come up the problem is internal and should be left to an experienced hands-on tech.

You've probably found an answer to this already but just in case...

You're most likely going to have to return the unit -- just receiver and subwoofer in my case as the sub was the only speaker not synching up.

Rather than dealing with their useless "Chat" web support, I would HIGHLY recommend calling their support # to get an RMA. Then request they EMAIL the RMA forms to you rather than snail mail. Also, make sure they have your correct name and info in their ridiculously poor customer database. They had my LHB975 serial # associated with some other person's name and address!! It literally took weeks and at least 6 calls to get it straightened out. Never again....if it dies again, it goes straight in the trash.

If u are trying to change the input from dvd to usb or the other inputs. All you have to do is hold down the play button on the front of the dvd home theater system until it starts to flash then press it again and keep pressing until u find the input u are looking for. It will rotate thru all inputs even the ipod input.

They will work only if the source signal is itself 5.1. If it's stereo then you must convert it to 5.1 using the Virtual sound setting (press VSM to access it and select 5.1).

You already said the Blu-Ray is working, so let's assume it's ok. Other source(s) don't produce surround so that leaves it (them) orthe one place they all come together - your receiver / theater system. Multichannel sound will only come from properly connected digital sources. Is that the case?

There is something wrong with the DVD drive assembly inside. If you're brave, take it apart and check on what is making the noise. Also, try using a q-tip to clean the laser head if it's accessible.

If that doesn't help, it's time for a new DVD player.

This is why I always recommend people buy a home theater system without a DVD player built in. The DVD player is the weakest link, and stand alone DVD players can be purchased for as little as $25 depending on if you want upconversion or not.

If you cannot get the DVD player working in your surround system, just replace it with a stand alone DVD player, if you can, check to make sure there are audio inputs on the back of the receiver. If there are no audio inputs on the receiver, you will have to get the entire surround system replaced. If so, purchase a separate DVD player and surround system.

FIRST- double check that the center channel is hooked up in the center channel connection. we have all made this mistake. second if you are watching a movie through a dvd or bluray player be sure that both your audio L/R rca's or hdmi cable's are plugged in. I do not know if your are on cable or satellite? Double check the connections. Be sure that the that if your can select your sound preference turn it to 5.1 surround or matrix. hope this helps

I used to have a setup pretty much exactly how yours is hooked up ( Different brand name equip. but basically the same setup) and I had to enter the custom setup screen for my home theater system and there was a setting there that allows you to choose between using a digital optical cable or a digital coaxial cable. I don't know if this is the exact same thing you have but it's worth a try because it sounds like it has to be a setting because like you say sound comes out of the t.v. ( and yes that is not acceptable) so you almost have got it. Keep at it, you can't really mess anything up by hooking up something wrong, it just won't work. Good Luck.

The LCD display has current flowing from all inputs possible and lighting up the entire display. If the system is otherwise working in the sense that sound is all right, then get the LCD display changed since the liquid in the LCD has spilled over the entire display causing it to malfunction. If the sound is affected too then check the internal fuse too ...........sodeep

Hi,
This problem is due the dvd problem may also take place but some times wiring loose connection may happen. so kindly check with this and if you still found problems please feel free to contact us, to get the solution.

I have a lg dvd/surruond sound and the remote suddenly stopped working. I bought a new lg riginal remote but still nothing, any thoughts?

You can't. You need a remote.

Replacement remote control for LG LH-D6230

Remotes World https://remotes-world.com > LG Replacement remote control for LG LH-D6230 with all functions of original one. It replace each button of original remote control. You will receive it with ...

See page 36 of this manual. It may help. https://gscs-b2c.lge.com/downloadFile?fileId=N9iqwMbFNb6ZzkUVITsZfQ

To reset your LG LHB 625, follow these steps: Turn off the device and unplug it from the power source. Wait for a few minutes and then plug it back in. Press and hold the STOP button on the front panel of the device for at least five seconds. The display will show "INIT" and the device will reset to its factory settings. LG LHB625 Product Support :Manuals, Warranty & More ' LG U.A.E.

Instead of aux (Blue Connector of PC Sound), try using head phone jack (Green Connector of PC Sound). It if is working fine, uninstall sound driver of your PC, restart PC and install sound driver again. Your problem will be fixed.

The back of the lry517 has 2 sets of audio outs and 1 set of audio ins. If you are using the component video outs, use the audio outs to the right of the component outs. If you are using AV1, it should be the audio to the left of the component outs. The tape's audio may be very low, try turning up the tv volume? You could also try adjusting the tracking? Have you tried using the AV1 outputs? It would be Composite Video and stereo audio.

Help in the link https://www.google.com/search?q=LG+DM5660K+DISPLAY+PROTECTION