20 Most Recent Danby DDR607EE Dehumidifier Questions & Answers

Bad smell coming from dehumdifier

Lin, the air intake filter may need cleaning and the water collection bucket may have a mold and mildew buildup. Cleaning both things, may solve the smelly problem.

Danby DDR607EE... | Answered on Feb 26, 2012

1 Answer

My Daby dehumidifier will sometimes have coade P1

don't know what the P1 code means, but maybe your demand of 50% and low fan is not able to be achieved so the unit will increase the CFMs (high speed on fan) to try and reach the 50% humidity level you are asking it to do within a certain time period.

Danby DDR607EE... | Answered on Jun 11, 2011

1 Answer

I purchased danby dehumidifier less

According to your Owners Manual:

P1 is part of a normal function of your dehumidifier. When your compressor is working it will build frost on the evaporator coils. When there is enough frost on the coils the unit will go into a P1 deicing program. This deicing cycle will last anywhere from 15-45 minutes. Once complete it will automatically resume normal function. The cooler the room the more often this function will turn on.

If you think it's still staying ON to long, contact Danby Consumer Help 800-263-2629

Hope this helped you.

Danby DDR607EE... | Answered on Apr 29, 2011

1 Answer

The P1 light is on , percentage of temps not

P1 is code for defrosting. Once it's done defrosting it should start operating

Danby DDR607EE... | Answered on Jan 06, 2010

1 Answer

My Danby dehumidifier leaks out

The drain tube or hole that drains into the bucket is probably clogged.

Turn the unit OFF and remove the bucket. Look in the cavity where the bucket was removed for a drain tube or drain hole. Using an 18" long plastic Zip Tie or something similar (No wire coat hangers) , that's appropriately sized to fit in the hole. Carefully feed the ZIP Tie into the hole or tube and thread it as far as you can. At some point the drain will curve, but you have to carefully get past this point. Once the Zip Tie has reached as far as it can, slowly pull it out while rotating it. This will loosen the clog. Once you have it half way out, be prepared for water to follow. This method should solve the problem.

Danby... | Answered on Jun 26, 2020

0 Answers

Problem with Danby dehumidifier not collecting any water

Danby... | Posted on Nov 25, 2019 | Be the first to answer

1 Answer

I am looking for a manual for a Danby dehumidifier model DDR070BBCBD8. Where would I find one

try searching for " Danby dehumidifier model DDR070BBCBD8"

Danby... | Answered on Oct 28, 2019

1 Answer

I would like to get an owner’s manual for a Premier Danby R410A Dehumidifier

try looking here and using a search engine next time.
https://www.manualslib.com/brand/danby/dehumidifier.html

Danby... | Answered on Oct 28, 2019

1 Answer

Have Danby dehumidifier, turned on first time this season,fan & all displays worked fine, but compressor never went on. Removed back panel & compressor is very hot.

Be careful. i do not know. set at highest setting and let it run. while running, reduce setting to the lowest over a few minutes. at a lower setting you should be able to tell that the compressor has started. run it for 5 minutes, then
unplug your machine. next, feel the cooling coils to see if they are very cold. if they are not cold, your unit needs to be serviced.

Danby... | Answered on Oct 02, 2019

1 Answer

Model Danby dehumidifier DDR70A2GP turns off after 30 sec. It has not been used yet this season to dehumidify clean finished basement. It is very clean and has worked well. Tech support was no help.

i don't know. my generic unit will do similar if i don't have the units moisture level set at a lower number. consider
using your lowest setting as a test.

Danby... | Answered on Oct 01, 2019

1 Answer