your booklet shows that the battery level is displayed on the bottom right of the screen of my new 1033. However, it does not. What do I press to display the battery level?
Well, I tried pressing and HOLDING down the mode button. The battery level display miraculously showed up. I’ve also read (yahoo answers) that battery level display will show up automatically when battery is low. Hopefully I won't have to do this every time I recharge the battery.
Posted on Mar 23, 2009
turns on to then turns right off
I'm not sure why this works for me, but I think it's worth a try:
1) First, take your SD card out of the camera.
2) Then turn on your camera and let it turn itself off.
3) Read the next step first and be ready to press the shutter release button (take a picture) right after the LCD screen turns on
4) With the camera lens pointed down towards the floor (aim down), turn on the camera. At this point the LCD screen should not be blurry anymore. Immediately press the shutter release after confirming that the LCD is not blurry. If the camera stays on and you can review the picture (most likely of your feet), then you are almost done.
5) Turn off the camera and re-insert your SD card.
5) This may not be a permanent fix, but point the camera lens downward whenever you turn on the camera. It should work normally if you do this. Mine worked normally (meaning I don't have to point it downward when I turn it on) after doing this several times. Your results may vary.
Posted on Jun 05, 2009
my kodak md1063 will not turn it won't do anything
replace rechargable batteries with regular AA alkaline and see if it will turn on, if it will you need a new battery pack
Posted on Jun 21, 2009
My Easy Share M1033 turns off immediately after turning on. After charging the batteries overnight the problem continues. I am unable to download, view, or use any features.
I have the same problem. Just tried a new battery. Same problem. :( I would love to hear any suggestions!!
Posted on Jul 06, 2009
Screen is blue reading error L03
Thanks in advace for your help
your camera will require service.
to setup a repair, please go to www.kodak.com/go/itg
Posted on Jul 27, 2009
New battery, full charge, still wont stay on. Does not stay on long enough to check the menu to see if the timer is set ???? Anyone have a better solution than trashing this and never buying a Kodak again!!!
The problem you describe is frequently the result of dirty/corroded
battery contacts in the camera. Try removing the batteries and
cleaning the inside contacts with a fine wire brush, steel wool, or
fine sandpaper. Remove any residue left from the cleaning, then
replace the batteries. Hopefully all will be well.
If the cleaning doesn't work you might want to check the Kodak troubleshooting guide at:
http://www.kodak.com/global/en/service/repair/troubleshooting/troubleshooting.jhtml?pq-path=6198
Posted on Aug 09, 2009
my kodak easy share m1033 camera turns off when i press any button
there is dirt or sand in motorized lens turn camera on and pop battery out before lens goes back in. Use a lens cleaning cloth and wipe all the outside of the camera lens well I also use a can of air and blew the three rings of the lens.I had to do this two times but now the camera works great
Posted on Mar 29, 2010
Kodak m1033 lenses stuck 'open'. Camera won't power on, just beeps and turns off when powered on. Camera froze when zoomed out max, removed batteries and now camera is stuck.
Hi,
Usually it's sand or grit interfering with the lens extension mechanism. Or the camera's been dropped with the lens extended. Or the camera has been powered on, but the lens had been blocked preventing its extension. Or the battery ran down with the lens extended. If the camera is still under warranty, before trying any of these, please please first contact your camera's maker to see if they'll cover the repair, or to determine how much they'll charge for the repair. Who knows, you might get lucky. But if they quote you a number that's higher than the value of your camera, you may want to consider the following methods.
Place the camera flat on its back on a table, pointed at the ceiling. Press and hold the shutter button down, and at the same time press the power-on button. The idea is that the camera will try to auto focus while the lens is extending, hopefully seating the lens barrel guide pins in their slots. Blow compressed air in the gaps around the lens barrels with the idea of blowing out any sand or grit that may be in there jamming the lens. Other variations include blowing with a hair dryer in “no heat” setting, or sucking the gaps with a vacuum (careful with this one).
Thank you!
Posted on Jul 14, 2010
I have a Kodak Easyshare M1033. When my camera turns on it wants the date and time set and none of the buttons work!
HELLO SIR
turn it on , Press Reset Buttonù
turn it off , still pressing The switch on button 10 seconds
It works for me
Posted on Aug 29, 2010
where i can get firmware for kodak m1033 camera?
Hello thanks for using Fixya
There is no Firmware available for this model online.Therefor the only option for this fault is to send it for repair.An out of warranty repair for this model for this fault is about 48
pounds+ shipping. KODAK also offers a trade up option where you will
have the opportunity to trade up to a newer model 25-30% cheaper than
the market price.
In order to arrange your Repair/Trade up: Click Here To Contact KODAK
I hope this solution will helpful 4 u
Please don't forget to click on Four thumbs which are given below and then give testimonial for my appreciation if it is helpful
THANKS & Keep Using fixya
Posted on Jan 19, 2011
426 questions posted
Usually answered in minutes!
601 Questions
559 Questions
492 Questions
428 Questions
435 Questions