Laser Canon imageCLASS 8180C Multifunction Printer - Answered Questions & Fixed issues


Are you using 3rd party cartridge or OEM replace the cartridge with OEM. Which cartridge does it say to check does your machine, have separate drum and toner cart. replace the right one.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Laser Canon... | Answered on Nov 22, 2015 | 37 views


Here's your support page. If you search "e000" you'll receive the following solutions.


Solutions
for e000 Issue: ERROR LCD: System Error E000

1. Reseating the Fixing Assembly-ICMF 8100 2. Resetting the machine-ICMF 8100 3. Verify/reconnect power cord to fixing assembly

Laser Canon... | Answered on Mar 28, 2017 | 2,935 views


You can download the Canon printer drivers from theirsupport WEB site. Please click on this link and select your model printer todownload : -http://www.usa.canon.com/consumer/controller?act=DownloadIndexAct

Laser Canon... | Answered on Jul 10, 2012 | 76 views


Hello,
To resolve the issue, please try reseating the fixing assembly. To do so, please follow the instructions below:
1) Unplug the power cord from the wall outlet.
Caution: The fuser unit and surrounding area can become extremely hot during operation. Perform the following procedure after the fuser unit has cooled down completely. Touching the fuser unit when it is still hot may result in burns. skumar_sreen_0.gif

2) Turn the lock release levers located on the back of the machine in the direction of the arrow and release the lock. skumar_sreen_1.gif

3) Hold the grip on the fuser unit and remove it. skumar_sreen_2.gif

Caution: The fuser unit weighs approximately 3.3 lb (1.5 kg), and it is heavier on the back side. Be sure to hold the grip securely when carrying a fuser unit. Dropping the unit may result in personal injuries. skumar_sreen_3.gif

4) Hold the grip on the fuser unit and install it securely. skumar_sreen_4.gif

5) Lock the fuser unit by turning the two lock release levers in the direction of the arrow. skumar_sreen_5.gif

6) Connect the power cord and all interface cables.
7) Plug the power cord in the wall outlet to turn on the machine.

Laser Canon... | Answered on Aug 30, 2011 | 253 views


There are Many MF8180C out there...and they are a good machine...however they had a Manufacturing FAULT and that is the POOR Quality of one Small plug on the FUSER unit RU5-8125....The FEMALE PLUG in the BACK of this machine has faulty Female Pins that Can and DO get pushed back into the base of the PLUG when the fuser is removed and reinserted...
Initally People THINK that the Fuser is BURNT out...BUT

Put a Multimeter across the White leads leadinginto the Fuser and then onto the White lead going INTO the Thermostat on the RHS and you should get a Full Circuit indicating that the heating element is IN FACT still OK ! Then Put the Multimeter on the other end of the plug and TEST the THERMOSTAT with the multimeter in the OHMS setting..you should get a resistance reading....Then the Thermostat is OK also....

NOW Just Look at the PINS in the BACK of the PLUG for the FUSER...most likley one/or two are recessed back in the plug...they should all be even at the FRONT of the PLUG....

Get some tweesers and Pull the little Pins Back out...so they are all lined up....

you will need to keep them there so get a TINY amount of Sicaflex (silicone adhesive-heat resistant...) and Put that UNDER Yes UNDER the Base of the PIN !!! NO UNDER !!!!
if you put in the pin the contacts will not meet....you just need to put a MINUTE amount under this pin to hold it out there.....IF you mess this UP you will have to HARD wire the Fuser in and that is a whole other matter.....

Good Luck Everyone I know this is the issue with the 8180c !!!!

regards Tony Gordon
www.whitelightfilm.com

Laser Canon... | Answered on Aug 04, 2011 | 311 views


Here's your support page.

There are various resets based on different messages.

Hope this helps!

Laser Canon... | Answered on May 01, 2011 | 354 views


Is it a white or black line?There can be a piece of paper in the drum cartridge or the drum is damaged!Scratched!Try replacing the drum cartridge!Good Luck!

Laser Canon... | Answered on Dec 07, 2010 | 121 views


E078 secondary transfer roller drive
mechanism fault

Possiblle causes:
Check the connector of the roller drive sensor.
Check the connector of the roller drive clutch.
Replace the main drive assembly (roller Drive
sensor).
Replace the drum cartridge (roller drive cam).
Replace the DC controller PCB.

Laser Canon... | Answered on Jul 01, 2010 | 3,998 views


I have a Canon Color Image Class MF 8180C with a system error code E078 - Trying to understand what it means and how to clear. Any ideas?

Laser Canon... | Answered on Jun 18, 2010 | 2,087 views


You can download the Canon printer drivers from their WEB site. Please click on this link and select your model printer :-
http://www.usa.canon.com/consumer/controller?act=DownloadIndexAct

Laser Canon... | Answered on Jun 16, 2010 | 251 views


If this was the case all the time, I would imagine you have an incorrect driver in the Laser Printer. You should be able to upgrade the drivers by contacting the the Canon Co.
If this is a new problem the static bar that runs across the drum has lost it's positive charge to produce the picture should be replaced ... its not cheap !

Laser Canon... | Answered on Jun 19, 2009 | 253 views


try to check your connection form your printer and if possible try reinstall the printer driver then try to run again the printer.

Laser Canon... | Answered on Jun 16, 2009 | 1,801 views


https://www.youtube.com/watch?v=ssBRM0WAY2Q

Laser Office... | Answered on Mar 20, 2020 | 24 views


I agreed with Nancy. I was also reading reviews on https://reviewspack.com/best-presentation-clickers/ and https://www.thedailytell.com/best-laser-pointers-for-presentations/ Logitech Spotlight is most powerful pointer the R800

Laser Office... | Answered on Jan 31, 2020 | 304 views


try unplugging it from the back, the switch might be broken.

Laser Office... | Answered on Aug 14, 2019 | 17 views


A fuser error is probably caused by a thermistor (detects an overheating problem). The fuser is probably best serviced by the manufacturer as an improperly serviced fuser could lead to a fire.

Laser Office... | Answered on May 30, 2019 | 20 views


"Error 6" indicates a common problem with LaserJet, a brand of dry electrophotographic laser printers from computer technology company Hewlett-Packard. One of such machines is the HP LaserJet 3390, an all-in-one printer that can print, copy, scan and fax documents.

Laser Office... | Answered on Apr 20, 2019 | 20 views


Fuser Near Life Warning-- check the user manual thats the best place for this answer
good luck
https://www.6ya.com/mrmmike

Laser Office... | Answered on Mar 02, 2019 | 23 views

Not finding what you are looking for?
Laser Canon imageCLASS 8180C Multifunction Printer Logo

Popular Tags

31 questions posted

Ask a Question

Usually answered in minutes!

Top Laser Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Barbat Nae
Barbat Nae

Level 3 Expert

509 Answers

Scott Kalvinek

Level 2 Expert

56 Answers

Are you a Laser Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...