Top 20 Samsung LN32A330 32 in. LCD TV Questions & Answers

moved you from computes to TV ok? well it can be any board seen inside, did you look first? power supply or logic boards. with no test equipment?, all you can do is guess. so start with the cheapest part. make sense?

hello: wifi , is not reliable. use Etherent cable from TV to router ! wins !you posted TVs to Computers, so will move you.what TV o TV model stated.MAC, how is it connected, to your router? all that tells me is the internet works on the mac. as does its browser..I will assume the TV shows, can not connect to local LAN , errors, (wifi in this case) gee use Ethernet cable.not netfix login failure not like me using 3 TVs to netflix, with a 2 TV max same time account. Also Netflix, Hulu and Vudu all 3 no longer supportold TVs running those old streaming apps with same name.they do not, (buy ROKU3 , wired)The went to a far better, streaming protocal your TV does not support, but again, NO TV even stated.By a long ethernet cable.no distance from TV to Router stated, nor type of walls between them,(concrete /brick horrible)WIFI is radio technology at its base) and weak signals.you skipped test 1;use ethernet, cable.this proves the TV works the TV app works and that Netflix, likes all that, with one simple test.a $10 cable, sold in all computers stores on earth.NO TV stated, full model on the rear sticker is it.lots of TV made in 10 years ,even olderand old is bad, in the realm of , Smart screen apps that are relics now.

I'd be looking at your internet speed. Sometimes when there are a lot of users at the same time the speed is reduced that will cause that. Have your provider test the modem to see if it is passing the speed you're paying for.

moved you to TV out of computers the model i picked is wrong but fixya is not samsung at all. and only few models indexed. smart TV sure, well do all the other streaming apps all fail too? if yes then the internet connection is bad. dont use wifi, it is hard to use, and very weak , slow and can overload easy for sure lots of neighbors on same wifi channels. so use ethernet cable cat 5/6 connect it to the router from TV to Router direct wired, see it does work, and now you know why it didnt before (WIFI sux deal)

MY TV It will get worse. if it self shuts down make sure vents at rear are call clean.

1. Samsung Smart TVs ' Technology To Change Your Life ' samsung.com‎

   Adwww.samsung.com/UK/SmartTV‎ Quick & Easy To Use, The New Generation Of Samsung TVs Is Our Smartest Yet. Types: Quantum Dot Display, SUHD Nano Crystal TVs, UHD Nano Crystal TVs, UHD TVs, HD TVs
   • Explore Samsung Smart TVs
   • Quantum Dot Display
   Edinburgh · 1 retailer nearby

Search Results Remote Control Method

1. Press the "Up" arrow key twice on your TV's remote control while in the Netflix app.
2. Press the "Down" arrow key twice.
3. Press the "Left" arrow and then the "Right" arrow. ...
4. Press the "Up" arrow four times. ...
5. Press the arrow keys to navigate to the "Deactivate" option, and then press the "Select" button.

How to Log Off of Netflix on a Samsung TV ' It Still Works ' Giving Old ...

https://itstillworks.com/log-off-netflix-samsung-tv-23508.html

Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://homenol.blogspot.com/ http://electronicshelponline.blogspot.com/ If blinks continue without any pause, the main board is faulty.

A model and make would help

Forgive on this one but I do not have a soundbar but wonder if it has any other connections like phono for input as to me hdmi would be a strange choice. Hdmi leads are mostly alike in they are fully wired and carry a wire which directs a device to listen to it when turned on, also some hdmi sockets (like the old scart) are blessed with options. Some may be input only while others set for in and out so it may be worth swapping connections on your TV to see if this changes the habit, though for me I would look to see if this soundbar has other sockets to use like phono (same with your TV if it has phono or scart socket options). Your TV instructions may show their ideal connection setup, otherwise you will have to shutdown your other item to stop it commanding the TV to switch through its sound. This "problem" is an old one with people using scart leads then I used to cut pin 8 (its control wire handing the descision to a user) but this new lead combo I do not know. Hope this helps.........

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main digital board.

If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/

It sounds like your tele maybe in store demo mode..To remedy this press the side button for volume up & whilst the volume up is displayed on the screen press & hold menu...On screen should be either Store/Shop mode Or Home/Standard mode select your preference & it should be ok.Good luck.

Carpet pop fault. Can't be repaired.

In the TV setup menu verify digital channel tuner selection is CABLE or ANTENNA to match the input.

Well, it has a bad T-con board. You'll have to pay for the part, but you can fix it yourself. The board can be replaced easily. The T-Con board is usually near the center of the screen when you have the back removed. Just look at the ***** holes with arrows pointing to them and take out only those screws. Once the back is off, you'll see a board under a metal cover(not always) The board has flat wide ribbon cables that go to the bottom of the screen. Get the numbers off the board and go here for parts: TV Parts Universal TV Stands DLP Chips ShopJimmy

Try leaving it unplugged for a little while.. at least 15 minutes and then replug and try.

Make sure your remote is working with fresh batteries. There is no history of how long you have had the TV etc. Use the manual power button if the remote wont work.

You could take the board out and look for a cracked solder joint on the board or a cold solder joint and repair. Bad solder joints are very common in TVs and monitors due both to poor quality manufacturing as well as to deterioration of the solder bond after numerous thermal cycles and components running at high temperature. Without knowing anything about the circuitry, it is usually possible to cure these problems by locating all bad solder connections and cleaning and reseating internal connectors. The term 'cold solder joint' strictly refers to a solder connection that was either not heated enough during manufacturing, was cooled too quickly, or where part pins were moved before the solder had a chance to solidify. A similar situation can develop over time with thermal cycling where parts are not properly fastened and are essentially being held in by the solder alone. Both situations are most common with the pins of large components like transformers, power transistors and power resistors, and large connectors. The pins of the components have a large thermal mass and may not get hot enough during manufacturing. Also, they are relatively massive and may flex the connection due to vibration or thermal expansion and contraction. To locate cold solder joints, use a strong light and magnifier and examine the pins of large components for hairline cracks in the solder around the pin. Gently wiggle the component if possible (with the power off). Any detectable movement at the joint indicates a problem. With the power on, gently prod the circuit board and suspect components with an insulated tool to see if the problem can be effected. When in doubt, resolder any suspicious connections. Some monitors may use double sided circuit boards which do not have plated through holes. In these cases, solder both top and bottom to be sure that the connections are solid. Use a large enough soldering iron to assure that your solder connection is solid. Put a bit of new solder with flux on every connection you touch up even if there was plenty of solder there before. press the helpful button and check video link Repair cracked solder joints What is Dry or Cracked Solder Joint and how...

My son once dropped our tablet and everything became fluted. I took the tablet to Samsung but having been overseas and the tablet was purchased in America they could not fix it as the parts needed could not be obtained. I had 2 options. I could either throw it away and lose all my files or try to fix following an intensive Google search. I chose the latter. I found a YouTube video in which the man walks you step by step in taking it apart and repairing several issues. Once I had the back removed, I found several 5pin wires in which they were all aligned perfectly with the exception of one. I carefully pushed it so that it became aligned, turned it on... and had a perfectly working tablet again. I am not sure if its safe for you to do this as I have always read the warning labels advising to never remove the back so not to be electro shocked but it might be worth you doing some research and seeing if its possible.