Top 20 Dual Electronics XDM6350 Car CD/ MP3 Player - Page 9 Questions & Answers

The blue one is normally related to automatic pop up antena, do you have one ? Now the red wire is a main source of power which should be connected straight to the battery.Now this blue wire may well be the remote which is connected to the amp and which your radio uses to wake up the amp and to start taking power from battery.Now for the non working problem, I would suggest you check there is power coming to it and all wiring are connected in the right place.Also many of these amp comes with internal fuse to protect themselves from high voltage...so check that too.

problem: you bought a dual; low quality... like they say, you get what you pay for; sometimes less

Yor code is 2058

Try to reset the radio by unplug the power source to the radio

Hello chrisuftring,

Here's a link to the wiring color code for the '95 Chevy Beretta.

You'll need to match the function of each wire from your head unit and the color code for that would be in your manual. Most aftermarket units are somewhat standard as far as power, accessory, ground, and speaker connections are concerned. But the wiring colors may be different for such leads as remote, power antenna, illumination, dimmer, and muting.

An Alpine head unit has the following wiring colors:
Blue - Power Antenna
Blue/White - Remote
Pink/Black - Audio Interrupt (muting)
Orange - Illumination
Red- Switched 12V+
Yellow - Constant 12V+
Black - Ground
Gray - RF Speaker (+)
Gray/Black - RF Speaker (-)
White - LF Speaker (+)
White/Black LF Speaker (-)
Violet - RR Speaker (+)
Violet/Black RR Speaker (-)
Green - LR Speaker (+)
Green/Black - LR Speaker (-)

With this head unit, you would wire Yellow to Orange, Red to Yellow, Black to Black, Orange to Gray, Blue to Pink, Gray to Light Green, Gray/Black to Dark Green, White to Tan, White/Black to Gray, Violet to Dark Blue, Violet/Black to Light Blue, Green to Brown, and Green/Black to Yellow.

Note that there are 2 "yellow" wires in your vehicle color code. You'll have to test them to determine which one is the accessory wire and which one goes to the left rear speaker. Using a 12V "test light" is the simplest. Connect one side of the light to ground. With the ignition ON probe the yellow wires. One of them should light the tester, the other one won't. Verify that the light goes out when the ignition is OFF and your have separated the redundant "yellows". The one that lit the tester is your 12V+ switched wire and the other one goes to the left rear speaker.

Hope this helps.

Hi Diaz,

We're going to need a bit more to go on. The amp configuration, single channel each or both on same, single or dual coil, that sort of thing.

The make and models of all components is always good to know from our standpoint.

You also need to think about power requirements when driving large speakers.

So comment back or repost with as much detail as possible.

Best regards
Mike

You can get manual here to set the clock.

http://safemanuals.com/user-guide-instructions-owner-manual/DUAL/XD7500-_E


Good luck and please rate

This is a useful free site for radio installation etc

http://www.installdr.com/

If it is a factory DVD deck installed up front, it won't let you watch a movie when you vehicle is in gear because it's a hazard and is illegal in many states and provinces. If it is an after market deck, there may be a work-around, however I do not have details as to how.

I got the same problem and i am desperate. Dose anyone know the answer? Email me, [email protected] Thanks! :D

first take out the stock head unit, after the colors of the wires originally from the car is usually red black yellow orange blue or gray, blue or gray w/ stripe, and purple or green, and purple or green w/ stripe. the head unit should have a power on it for the speaker wires those are the only tricky ones. color with stripe is negative. yellow for +12 black for -12 ground and red is for ignition, turn the radio on with ignition on. purple is usually rear and blue is usual front

The Apple iPhone 3G, iPod Nano 4th Gen, iPod Touch 2nd Gen, and any other newly released iPods can be controlled using the iPod adapter above; however, charging will not be possible unless you purchase the Scosche IFWA PassPORT charging adapter.

Hello dusashbrax,

The wiring color code for the 2002 Blazer is here. Just match up the function of each wire on the aftermarket receiver with the appropriate color wire from the vehicle.

A better solution is to purchase a vehicle specific wiring harness. Then you just match it up with the receiver harness color for color.

Hope this helps.

Hello southernbike,

With a 5-channel amp (stereo L/R front, stereo L/R rear, and subwoofer) you only need the two pair of stereo inputs.

You do not say which brand and model of amp you have, but most have an output configuration similar to the Alpine shown in this link. Connect the front and rear RCA's from your receiver, your vehicle speakers to the respective output terminals, and your subwoofer to the 5th channel terminals.

Hope this helps.

BEST THING TO DO IS GET A TEST LIGHT AN TEST ALL THE WIRES FOR POWER YOU SHOULD END UP WITH THREE BUT ONLY TWO ARE REALLY NEEDED CONSTANT POWER WITH IGNITION OFF AND ONE THAT GIVES YOU POWER FOR ACCESSORIES ONCE U OPEN THE SWITCH

you need to buy a switch that u can use to bypass the brake. you have to run it to the wire that you are suppose to run to the brake and you will have to switch the off and on button and then your tv will work without the brake.. i had to do it to my same exact TV..

hay try using a switch like the off and on ones wire it so when it on the unite thinks the the brake is on it should ground i think just make sure let me know how it works

The incar DVD player that you have I assume is connected to dual monitors in your head rests. Inphase do a good quality DVD very cheap, in the UK you can buy it for 150 GBP including 2 new head rest monitors. In the US there must be a reputable dealer than can offer a similar price for the same item or similar.

If you cannot access a existing grommet, just drill a small hole through the firewall on the passenger side. Take a moment and look carefully so you will not pierce or damage other parts. Usually with most vehicles you can find a good spot to make a hole. You can purchase a grommet to fit the hole you are making, or just goo it with silicone so the power line will be knick free and secure. Pull back the needed carpet and mating. You may even find a wiring harness under there that connects through the firewall, if so, you may be able to squeeze through the side of it.

Not too sure about dual cd players, but there is usually a reset button the size of a pin-hole behind the detachable face on most. Try holding it down for a few seconds to reset it. Hopefully that works! if it does then i would suggest buying a settings keeper when doing anything with the electrical system. Its a 9 volt battery that plugs into your cig. lighter. (I work at AutoZone, you can pick one up there)

~Derek~