Top 20 Audio Technica Audio-Technica ATH-W5000 Professional Headphones Questions & Answers

Use an alternative device connected to the input the turntable usually connects to. If both channels work ok the new turntable is clearly faulty and should be returned under warranty.

You should go back to the local repair shop and ask them to do the job right or to give you the money back you presumably paid. You have a legal right to have them fixed properly.

Having looked at the turntable it seems to mount the cartridge with two bolt like fittings. The Cartridge you want has two mounts on the side that will take those bolts. You will have to adjust the arm to compensate for the weight differences between the two cartridges, but once done it should play fine.

If you have replaced the cartridge then it must be the cartridge pre-amp that is faulty. If there are any other functions on the device such as CD, then it will not effect them. Unless there is crackling on any other function then the pre-amp has a problem. The pre-amp itself is generally a single IC. You can find it by following the turntable connection back to the inside of the amp. The signals will pass through the IC before being passed to the main pre-amp.

I have used this article to set up my dual turntable. Cartridge Alignment The Basics Explained Tracking force: 1.5 to 2.5g Your cartridge specifications are in the following link. Audio Technica AT91 Hope this helps?

There are a number of helpful videos on YouTube about this model turntable, it might give you the answer you need.

Contact this site Audio Technica Turntables Phono Cartridges Needles Accessories Also, they have a toll free phone number

Normally, yes. If you'\'re not sure how to track down the part that's broken, contact the maker for an ra to return it for service.

This is the only thing I could find online: 1 - shield 2 - left (hot) 3 - left 4 - right (hot) 5 - right

go to Audio Technica ATW T202 T8 VHF Handheld Transmitter from www parts express...

http://www.audio-technica.com/cms/resource_library/literature/cb45724a4bf698c6/p52300_atr2500_usb_om.pdf

The other is most likely a ground. However you should use a good magnifying glass and bright light to look for tale signs of the connection that is broken.

The battery has to generate quite a bit of power to energise the plates in a condenser mic. So wasting energy by powering an LED when it's not really needed is a bad idea. The light 'blinks' to confirm that you switched it properly. After that, it will only blink again when you move the power switch to OFF unless there's some battery warning indication built in. As for the mic not working; most of the time this is down to poor quality or broken cables; or incorrect connections; or the wrong settings on the receiver or mixing console.

In a typical configuration you will need to connect the receiver to another device such as a mixer console. The mixer is connected to an amplifier. And lastly, the amplifier is connected to speakers. Without more information, such as existing equipment in the configuration, I am limited to how much I can help you. What are you trying to acheive (band, karioke, voice reinforcement, etc.) What environment are you doing it in? What equipment do you have besides the mic and receiver?

The AT3525 handles very high sound pressure levels with ease, accepting as high as 146 dB SPL before producing 1% T.H.D. A switchable 10 dB (nominal) pad is built-in, increasing its capabilities to 156 dB SPL. An integral 80 Hz hi-pass filter provides easy switching from a flat frequency response to a low-end roll-off. The hi-pass position reduces the microphone's sensitivity to popping in close vocal use. It also reduces the pickup of low-frequency ambient noise (such as traffic, air-handling systems, etc.), room reverberation and mechanically-coupled vibrations.

The ATT switch will give you more or less volume, depending on your mixer. I start out with it ON and if volume is low, put it OFF. The 80 Hz switch is for rolling off the Sub Bass frequencies, use it if your source is Voice or Flute or such to avoid wind or breath noise. Enjoy...

The ATT switch will give you more or less volume, depending on your mixer. I start out with it ON and if volume is low, put it OFF. The 80 Hz switch is for rolling off the Sub Bass frequencies, use it if your source is Voice or Flute or such to avoid wind or breath noise. Enjoy...

Replace drive belt...slipping!

system preferences > sounds>