Canon MF6530 Black and White Copier - Answered Questions & Fixed issues
Canon MF 6530 Paper Jams
Hello,
it can be that sesor flaper in fixing unit has an slow response or the sensor is faulty. Also it can be that this is delay jam due to worn out paper feeding roller, or faulty pressure in fixing assy.
Recommendation is to call service!
9/17/2011 9:44:43 AM •
Canon MF6530...
•
Answered
on Sep 17, 2011
•
333 views
My printer's feeding mechanism or
I think that is not problem with your printer,
that is cause paper was moist. and sticky.
solution make the paper became warm (put on the warm place or don't use air conditioner in this room)
5/13/2011 6:21:06 PM •
Canon MF6530...
•
Answered
on May 13, 2011
•
55 views
Unplugged it and now it
Welcome to Fixya
Try this troubleshooting procedure:
With the machine on, unplug machine from surge protector or outlet. While the machine is off push the Copy, Scan, Start button in that order 3 times. Plug the machine back up. The machine should initialize and be ready to copy.
Please let me know if you have furhter questions.
Thank you for using Fixya!
If you need further help, reach me via phone at
https://www.6ya.com/expert/elixirjose_00375ea24bd8141b
5/4/2011 9:28:15 PM •
Canon MF6530...
•
Answered
on May 04, 2011
•
75 views
Paper wrinkles up time it gets about an inch in
Hello Hawk.
My name is Jeff and I work for a company named Advanced Office Systems which has been in business for over 30 years.We are based out of Knoxville Tennessee and unfortunately can't come to help.But I feel confident my service manager may be able to help you find a service provider in your area.He's a good man named Dan Llewellyn (pronounced "loo ellen").His number is 865.966.0770 ext 217. A busy man ,but a good man. I hope I have helped you so if you don't mind please acknowledge my help thru FIXYA. Thanx and I wish you the best.
1/15/2011 2:16:24 PM •
Canon MF6530...
•
Answered
on Jan 15, 2011
•
96 views
Frequently when I turn on the printer the red
Hi,
I presume that the problem is in MFP crg. recognition.
When you remove toner crg. on right side in the MFP you will see black "gear" with one metal pin, which goes out when you close the door. Apply small amount of WD40 or similar and open close door for few times. If it does'nt helps you need to dismantle the copier and clean the whole section...
Hope that helps!
By the way didi you try with another crg.?
12/28/2010 8:55:28 AM •
Canon MF6530...
•
Answered
on Dec 28, 2010
•
52 views
How do we reset printer to original settings?
press *2 then 8 then *again.machine will be in service mode go to clear,then choose all then press ok
machine will be in default mode,pleaze wait msg will apear,turn off and on again,i hope u will be happy
11/18/2010 9:52:02 PM •
Canon MF6530...
•
Answered
on Nov 18, 2010
•
161 views
Will not print
if you have problem, wich is that you have blank copies and prints, the problem is in metal pin caled laser shuter.
Call service.
6/28/2010 4:27:06 PM •
Canon MF6530...
•
Answered
on Jun 28, 2010
•
128 views
677ERR
your print board has a failure
8/25/2009 10:08:45 PM •
Canon MF6530...
•
Answered
on Aug 25, 2009
•
31 views
MY CANON MF6530 GETS GETTING PAPER JAM.
Where doeas the paper get stuck.
If just out of the tray try cleaning the paper pickup rollers.
f it gets up the fuser, can ypou see if the fuser rollers have baked on toner or dirt, if so you probably need them cleaned or replaced.
If the paper gets past the fuser then there is probably a problem with the output sensors, perhaps stuckin the wrong position or faulty, again further investgation via strip down would be required
3/23/2009 8:04:08 PM •
Canon MF6530...
•
Answered
on Mar 23, 2009
•
479 views
I have a problem with my canon printer g3411. It has an error P03 but no paper jam. How do I solve my problem
Error P03 on a Canon printer typically indicates a paper jam, even if you cannot physically see any jammed paper. Here are a few steps you can try to resolve the issue:
- Turn off the printer and unplug it from the power source.
- Carefully check the paper tray and inside the printer for any jammed paper or debris.
- Remove any jammed paper or debris you find.
- Plug the printer back in and turn it on.
- Attempt to print again.
If you don't see any paper jammed in the printer, there are a few other things you can try to resolve the error P03:
- Try resetting the printer. To do this, turn off the printer, unplug it from the power source, and wait for a few minutes before plugging it back in and turning it on.
- Check the ink cartridges and make sure they are properly seated and have enough ink.
- Clean the printer's rollers. Rollers are the small rubber wheels inside the printer that move the paper through the printer. Over time, dust, debris, or ink can build up on the rollers and cause paper jams. Cleaning the rollers can help resolve the issue.
- Try to update the firmware of the printer. Sometimes, a firmware update can resolve the issue.
- Check the printer's settings, ensure that the size of paper loaded match the size of paper set in the settings.
If the problem persists after trying these steps, you may want to contact Canon support for further assistance.
3/19/2024 2:50:12 PM •
Canon Office...
•
Answered
on Mar 19, 2024
•
384 views
Not finding what you are looking for?