Mitsubishi WD-73736 Television - Answered Questions & Fixed issues


There are some adjustments should be done after the DLP chip replacement. If you wish to get some details; visit the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/

Mitsubishi... | Answered on Jan 22, 2017 | 69 views


the model is amitsubihi MD-73736

Mitsubishi... | Answered on Jun 13, 2013 | 192 views


Remote sensor is always on front of set behind a clear or tinted small lens and inside it usually is on a circuit board .
12_15_2012_1_40_18_pm.jpg

Mitsubishi... | Answered on Dec 15, 2012 | 328 views


It means no signal found----double check entire hookup and of course make sure box on and connected to the correct input on the set.

Mitsubishi... | Answered on Aug 29, 2012 | 25 views


You need a 3D Blue ray player and 3D glasses. Make sure that the 3D feature is turned on on your Mitsubishi. You also have to have HDMI 1.4 cables. Anything lower will not produce 3D

Mitsubishi... | Answered on Apr 27, 2012 | 75 views


Bad capacitors on TV is usually found on power supply board..

it is connected next to power cord

Like this:


1_6_2012_12_33_13_pm.jpg

Mitsubishi... | Answered on Jan 06, 2012 | 165 views


HI:
The normal usage time for lamps are 6500 hours, thats a little under three years depending on the use of the television, These lamps last longer when they are not turned off and on all the time. The constant heating and cooling prematurely wears out the lamp, also on Mitsubishi lamps have a filter on their lamps that geta cloged with dust from the exaust fan, causing heat to become traped in the lamp compartment which will cause the lamp to blow premautrely, using a compressor try cleaning this filter every 6 months or so for longer llamp life.

Mitsubishi... | Answered on May 01, 2011 | 73 views


Mits has had an excessive number of problems with color wheels in some of their optical engines. Provided you replaced the lamp with OEM parts I would suspect the color wheel is causing the noise as well as the shutdown issues.

Bill W
integrityhomeworx.com

Mitsubishi... | Answered on Mar 14, 2011 | 435 views


Thats a mechanical adjustment called keystone. The service manual sjould outline that proceeduer for you. You can get the service manual by download link from www.servicemanuals.vstore.ca

Mitsubishi... | Answered on May 25, 2010 | 101 views


Hi,
Click Vizio Support to download user manual of VW37LHDTY30A.
Hope this info will help you.
Thanks.

Mitsubishi... | Answered on Dec 01, 2009 | 59 views


The Ballast that ignites the Lamp could cause the Lamp to fail and/or cause a buzzing noise. That being said, the Color Wheel in the Optical Block assembly could also cause a similar symptom. If Mitsubishi would be willing to help with the Lamp cost, I would call a local Mitsubishi repair facility to install it and see if the noise is still there and find out exactly what is causing it. Mitsubishi Customer Service Phone number is 1800-332-2119.
I hope this helps,
Skyassoc

Mitsubishi... | Answered on Oct 26, 2009 | 1,046 views


The unit is likely VERY VERY dirty..which makes the unit overheat and also generate a weak picture...as well as stress the lamp. It is probably not worth fixing if it will not turn on at all anymore and you have little money in it. Parts could be very hard, if not impossible, to find.

Mitsubishi... | Answered on Aug 11, 2009 | 72 views


You should be able to use the device button on the remote control. If this does not work, try going into the menu and disable the home theater mode. The home theater2.gif mode locks the TV to input 1.

I hope this information allows you to resolve this issue.
If I have helped you, please help me, and rate this suggestion the highest FixYa rating. (Two Thumbs Up)
Please Note: If you can not rate this post with the highest rating, then please do not leave any rating. I am doing this for free and I do not think that any rating other that the best is needed.
If you need further assistance please comment to this post and I will try to help you further.

Mitsubishi... | Answered on Aug 05, 2009 | 82 views


Take that mother back to the store and tell them to quit dropping there Televisions i am serious about that statment. There is a resister that came loose inside the TV it needs to be repaired,

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

Mitsubishi... | Answered on Apr 22, 2009 | 124 views


take it back!

Mitsubishi... | Answered on Mar 27, 2009 | 282 views


i'd take it back!  it's obviously defective.  TV's are supposed to last longer than 4 months!

Mitsubishi... | Answered on Mar 27, 2009 | 176 views


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
https://homenol.blogspot.com/
https://electronicshelponline.blogspot.com/
If blinks continue without any pause, or the LED light stationery; the main board is faulty.
Search the site by type in the "brand name" to your device; [Exclude the model number], in the "Search box at the top right of the display window of the Homepage" to get gathered related posts. See the site by a desktop. Mobile view has no search box. If you are viewing it by your mobile, see it in webview/

Mitsubishi WD... | Answered on Jul 10, 2018 | 127 views


Basing the replacement of the board on the clicking sound of a relay trying to close is not a safe bet. The first thing you need to do is check the bulb. Then there is a ballast board and then the Power supply board. Parts might be hard to find. Use the website I listed to see what part numbers are then google it or look on eba or amazon for those parts. Mitsubishi WD 60C8 TV Parts

Mitsubishi WD... | Answered on Jan 18, 2018 | 91 views


Most likely a fuse blew when the lamp blew, there is internal fuses on the power supply board on these mitsubishi's, if the fuse is ok though then most likely another component somewhere failed.

Mitsubishi WD... | Answered on Jan 02, 2018 | 121 views

Not finding what you are looking for?
Mitsubishi WD-73736 Television Logo

33 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1258 Answers

The Knight
The Knight

Level 3 Expert

76416 Answers

Todd Hill
Todd Hill

Level 2 Expert

433 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...