20 Most Recent
Mitsubishi WD-60735 Projection Television - Page 8 Questions & Answers
How do you change a lamp on a wd-60735
First order the correct lamp for your TV. Order from
www.mitsuparts.com if the unit is out of warranty. The lamp part number is 915B403001. Next make sure the TV is off and has cooled for at least one hour. Use a Phillips #2 (large) screw driver to remove the cover from the back of the TV (on the lower right hand side). Next loosen the two screws (Phillips #2) that hold the lamp cartridge (they do not come completely out of the cartridge). Open the bag that comes with the new lamp and set it aside. Grasp the handle on the old cartridge and pull it straight out. Put this lamp into the bag. (Be careful to avoid tilting or rotating the lamp since that could cause glass to fall out of the unit.)
Carefully handle the new lamp (do not touch the glass - wear gloves if possible), Insert the lamp cartridge into the TV in the same orientation as the one you removed earlier. Push it into the TV until it is fully seated. Tighten the two screws with either your fingers or the screwdriver. Do not overtighten the screws. Replace the cover and tighten that screw.
You can get the manual from Mitsubishi support:
http://www.mitsubishi-tv.com/support.html . Click on Product Documents and search for the model number. The directions start on page 75 and includes pictures of the procedure.
I hope this helps.
Cindy Wells
Liquid got between frame and screen how do i get
need to dis assembly the frame of the tv and take the 3 screens out and cleaned may sure you put this back in the same way you took it o each side is different do not use any cleaner like windex
I have a green screen
I take it your DVD is plugged into your Video in and your Cable is plugged into your RF connector or Antenna input. IF this is the case, you might have a bad RF cable. Can you run RCA cables from your Cable box to your TV? This should help with quality of picture as well as better sound. RF Connectors are old school. In todays market, they don't need to be used anymore. I don't use my RF connectors at all. I hope this helps you.
Mitsubishi WD-60735 has verticle bars with broken
This is your digital module going bad. The only way to repair this is to send your Light Engine Cube Assembly to Mitsubishi to be refurbished. I believe they charge the consumer 300.00 to rebuild. I have seen 3 just this past week. All DLP sets are failing at a high rate now.
Picture is dark
change brightness setting
i hope this helpfull
please rate my answer
thanks for using fixya
My Mitsubishi wd-30765 started to buzz. Then it
WD-30765 ???
Please recheck model number as WD-30765 is incorrect/ invalid model number.
Buzz sound could be of bad color wheel in light engine and cause of problem.
Let me know correct model number to diagnose problem in your tv.
Thanks.
What causes the lamp to blow out if the lamp has
Lamps do go bad much like head lights. Some last longer than others. Most have a life expectancy
of 3000 to 5000 hrs of use. I would make sure the unit has good ventilation and exhaust ports are open and not clogged with dust. These are the only precautions I can advise you on. I would also use only lamps that come complete with their cages from the manufacture or their part suppliers.
They may cost a little more but they are more reliable.
I hope this helps,
Skyassoc
Replaced the lamp. still have
Red light idicates a bad lamp or lamp ballast. There are so many places selling cheap aftermarket and even rebuilt lamps that simply are junk and most wont work.. Especially on Mitsubishi's If you paid less than probably 130.00 id say you got a junky lamp and odds are thats your problem.. If you got a good quality lamp then i would suspect the ballast but on that model hasnt been a common problem..
My picture is darker than
Your bulb is about to die. Order a new one soon and replace it now, or replace it when the other bulb burns out.
Same thing happen to me.
The lamp in the tv no longer works how do i
On the right side from the rear you will see the lamp door cover. Remove that and the lamp cage will be inside, it should have 2 phillips head screws holding the lamp in. The rest is
elementary. I recommend getting it from
dlplamps.com
My TV made a noise
The tv old projection lamp in the tv now like 1 1/2 or 2 yeears?The tv LED "LAMP" light up or flashes the projection lamp is dead.Yes,the tv require a new projection lamp.
I have a wd-60735. It
No Lamp will not cause dimmer picture,problem maybe in the power supply board these sets are well know for having alot of Bad Capacitors.
This may or may not help but Go to Encompass Parts Distribution and see if they Service Manual - Encompasds Parts Distribution
or try retrevo.com
I have a old school
Hi,
First, i would like to inform you that this could be an internal failure as well.
This
model is equipped with a self-diagnosis feature to help
with diagnosis of shutdown problems, to activate this turn the unit on
let it shutdown then press the input/or device and menu buttons on the
front panel simultaneously and hold them in for 5 seconds after 5
seconds the power LED on the front panel will blink a two digit
sequence. This will be one set of blinks a short pause then another set
of blinks, this will repeat 5 times.
Let me know,so that we could
Proceed.
Hope i helped you.
Thanks for using ' Fixya '
and have a nice day!!
Not finding what you are looking for?