20 Most Recent General Electric WBSR3000G Top Load Washer Questions & Answers

0helpful
1answer

Won't spin out washing machine

Hi,

Problems with a washing machine not spinning or not draining are often interrelated..

If you are having a problem with your top load washer then check out thistip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkoutthis tip...

Front Load Washing machine not draining and or not spinning


heatman101
8/14/2011 9:58:14 PM • General Electric... • Answered on Aug 14, 2011
0helpful
1answer

It won't pump the water

Hi from retired Englishman in SW France,

I think you will find that most, if not all, washing machines have a separate electric drain motor/pump.If you have not checked and cleaned the filter I strongly suggest you try it. Here are my general guidance notes on the subject ;-0)
--------------------------------------------------------------------
Sorry but I do not know your particular machine BUT I would suggest as a first step that you clean the drain motor lint tray/filter. So many 'faults' are caused by blocked filters. The motor is unable to drain all of the water in the allotted time.
If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!) and held in by a round cover/knob.

REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT!

It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. If it doesn't work then the motor is malfunctioning!

Hope the filter is the problem and good luck!
John C
3/1/2011 8:25:32 PM • General Electric... • Answered on Mar 01, 2011
0helpful
1answer

GE washer wssr2070v1 will not spin.

If you hear the motor running but nothing is happening then check the belt on the bottom of the machine and the brake to make sure that the belt is not broken or stretched and also that the brake is not holding the drum
5/23/2009 2:53:40 PM • General Electric... • Answered on May 23, 2009
0helpful
1answer

I have super general washing machine 7kg top load showing error code e3

e3 mean to much water in washer,check inlet valve, are call a techicain to solve your problem
7/15/2021 11:59:21 AM • General Washing... • Answered on Jul 15, 2021
0helpful
1answer

Error 4 in super general SGW 620 top load washing machine..how to solve ?

It has a blocked sensor pipe. Clean and service the machine.
3/11/2021 4:14:59 PM • General Washing... • Answered on Mar 11, 2021
0helpful
1answer

How can i fix F8 error in automatic washing machine? Super general sgw721 top load

Too much water in the machine. Check the drain pump, outlet pipe and filter if any.
12/4/2020 10:11:45 AM • General Washing... • Answered on Dec 04, 2020
0helpful
1answer

I Have E60 Error on my washing machine Super General SGW-8100, What that means? Somebody mentioned reset button to press for 5 seconds, where to find it??

check out this youtube video on e60 error https://www.youtube.com/watch?v=-6iNKH9qhKU
11/30/2020 9:05:39 AM • General Washing... • Answered on Nov 30, 2020
0helpful
1answer

Super General Washing Machine No Power on LED display? we already check the fuse and replaced

check voltage from switch to power board if ok bad display
10/24/2020 8:19:06 AM • General Washing... • Answered on Oct 24, 2020
0helpful
2answers

Error 2 super general washing machine

I have super general washing machine model is sgw 620 this machine coming error E5
6/18/2020 5:47:27 PM • General Washing... • Answered on Jun 18, 2020
0helpful
1answer

Super general sgw720 washing machine can't spin. when starting for wash it shows 42 min.it stops 27th min.then just rotate tub it starts and again 17th min same issue.we set only spin same issue

i don't know. i repaired same condition on different washer. it was the lid safety switch/pin contact. i tested by pushing pencil in hole where safety pin goes. DO NOT USE MACHINE WITHOUT WORKING LID CLOSED SAFETY LOCK. you could break an arm / hand. i slid top off washing machine and moved lid switch back so ' lid pin ' would contact safety switch. if this is the cause, you may need to replace this low cost switch.
1/7/2020 6:55:12 AM • General Washing... • Answered on Jan 07, 2020
0helpful
1answer

MY Super General SGW 1201 IS showing E01 error stops working, once I open the door and shuts it continues, its coming as and when

you can google you super general swg 1201 E01 error for instructions to trouble shoot. or try you tube.
5/4/2019 8:34:27 PM • General Washing... • Answered on May 04, 2019
0helpful
1answer

I have super general sgw620 washing machine,my drain area is upper and on the wall. can u pls advise how to use this machine with upper drainage system

The drain on the wall is called a Stand Pipe. It is designed to be higher than the washing machine so that you do not flood the building every time you do a load of wash. The Machine has a built-in pump to pump the water out of the machine when needed. You will need to attach a washing machine drain hose to the machine. You should be able to find one at Lowes or Home Depot. https://www.lowes.com/pd/bosch-drain-hose-extension-kit-gray/1000024537?cm_mmc=shp-_-c-_-prd-_-app-_-google-_-pla-_-186-_-sosaccessories-_-1000024537-_-0&kpid&k_clickID=go_625713068_34614756550_111134534590_pla-261169297148_c_9027729&gclid=EAIaIQobChMIwc_2u8_-4AIV9x6tBh1fSA3fEAQYAyABEgJjjPD_BwE
3/13/2019 7:45:55 AM • General Washing... • Answered on Mar 13, 2019
0helpful
1answer

I have super general washing machine model is sgw 720 this machine coming error E4


Run the machine empty to see if you can clear some of the soap residue, E-4 is "suds lock" error and is usually due to using too much detergent.
10/3/2018 8:39:25 PM • General Washing... • Answered on Oct 03, 2018
0helpful
1answer

General alarm shows on display yet the machine is clean how do I resolve this?

when you let people know what type of machine it is then maybe we could help but go to the manufactures and download the user manual and check in the trouble shooting guide eric
1/2/2018 10:09:42 PM • General Washing... • Answered on Jan 02, 2018
0helpful
1answer

GE Front Load Washer wbvh5200 doesn't spin & complete wash cycle

hi if you are familiar on how to use an electric multimeter this is what you do access to the motor which does the washing / spinning find the cable that are attached to the motor remove cables screw them on to a separated connecting block now you select a program ( awash ) with no laundry start the program then set you meter to volts hold the meter prongs on the cable that you have already put into the block hold firm the prongs in each wire you then should get voltage ( hold for 5/8 minutes if the voltage do not get interrupted there is nothing wrong with the control board but the motor is faulty and vice versa
1/2/2018 12:34:33 AM • General Washing... • Answered on Jan 02, 2018
Not finding what you are looking for?
General Electric WBSR3000G Top Load Washer Logo

Popular Tags

7 questions posted

Ask a Question

Usually answered in minutes!

Top General Washing Machines Experts

Oloyede Monsuru

Level 3 Expert

1468 Answers

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

sheakhly

Level 1 Expert

33 Answers

Are you a General Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

General Washing Machines

  • General Washing Machines

Most Popular Question

won 39 t spin out washing machine

  • Washing Machines
Loading...