Top 20 Krups XP7225 Espresso Machine Questions & Answers

0helpful
1answer

Filling of machine required

Did this problem exist before your fix? Make sure the hoses are the correct way around on the flow meter and check the wires are plugged on correctly. It is possible to offset the plug on some models.
3/13/2014 8:36:23 PM • Krups XP7225... • 156 views • 0 helpful votes
0helpful
1answer

Krups xp 7225 replaced piston, reassembled and is now dead, power switch seems ok and all wires firmly attached

Your Power Switch Part No Ms-0675088 need to change.,yourmachine have appear any error No ? God BlessJoseph
7/23/2012 6:12:59 PM • Krups XP7225... • 330 views • 0 helpful votes
0helpful
1answer

Error code OE

circuit board need resetting
5/23/2012 10:17:08 PM • Krups XP7225... • 419 views • 1 helpful votes
0helpful
1answer

My Krups xp7225 suddenly stopped

xp7225, the grinder in possibly plugged at the discharge,you may have to remove the grinder to get it cleared-when doing so check the O-rings on the top plunger.to disassemble start by removing the front trim. this is TRICKY, pull out a bit at the bottom and slide up at the same time it should release and you can access the shrews and remove the top, OYA remove the water tank and bean bin! then remove shrews on top including under the the grate and the piston has a spring a the discharge shoot gently move it wile removing the 2 shrews holding the grinder in place, you may be able to gently lift the grinder up. wires are a bit long, place a rag or paper towel at bottom of pocket to prevent anything like shrews from falling though and you can remove the motor from the grinder by removing the shrews under it with a stubby shrew driver. BUT if the wires will not pull out enough..THEN you have to remove the sides and back.. remove by taking out the screws at the front and top leave the bottom and front in place..slide the back and sides together away from the back.....open the cover over the wires MARK and record all wire positions unplug the the wire to to the grinder follow wires to find them.....if you have to untangle by removing the board USE CAUTION the connections are FRAGILE...up the spade connections first then lift the top of plastic and pull the board out and away!!! BE SURE TO NOTE WIRES there is ON wire diagram available !!!!reverse to put things back together... GOOD LUCK
8/31/2011 6:25:36 PM • Krups XP7225... • 298 views • 1 helpful votes
0helpful
3answers

Code error 06 in Krups

Hi,

The error 06 comes after start up and machine in auto test - happens because of more than one problem. However first unplug the machine and then remove the water tank filter (the cylinder inside the water tank) and wash it up. Actually the filter should probably be replaced. However fix it back in the water tank and tide it safely upon the exit ring.Now restart the machine and let it perform the automatic self testing.

Please get back to us if you have any further query.

Have a nice day.

12/8/2010 11:01:10 AM • Krups XP7225... • 8,710 views • 1 helpful votes
0helpful
1answer

KRUPS xp7225 LEAKS FROM THE

For mine, the solution, which also applies to other similar Krups machines, was to replace the seal at the bottom of the boiler. (#MS-5015004). This seal was torn. While in there, I also replaced the piston (#MS-0697072), which seemed like a good idea, since its O-rings seal the top of the chamber. I got my parts from Nelson Appliance.To replace the seal (from memory, so there might be some details missing or incorrect):1. Remove drip tray, coffee drawer, water tank, and side bin2. Remove top metal cover and one screw underneath that holds down the plastic insert3. Remove the one screw that holds the cover inside the bean hopper and carefully pop off the grinder adjustment knob. The hopper should now come off.4. Slide the front plate (gray/silver plastic) up until it pops off. Remove the four screws underneath it.5. Remove the screws from the top of the unit (two at front, one in a recessed hole in the back).6. Remove the two screws under the water tank. 7. Pry/pop the top off, and pry the side/back cover off.8. Unplug the grinder from the circuit board, remove the two screws that hold it in place, and remove the grinder.9. Remove the coffee line from the piston. Remove its clip and then remove the two screws underneath it.10. At this point, you will need to disconnect most of the other wires from the circuit board or the components they go to, and you will need to unbolt the piston carrier, so that you can remove the frame that holds the grinder. 11. Remove the three screws that hold the boiler to the base.12. Holding the shaft from underneath, remove the screw that holds the screen in the middle of the plunger in the boiler. 13. The plunger and shaft can now be removed. 14. The seal goes in the hole at the bottom of the boiler that the shaft runs through. I used a toothbrush handle to push the new one into place from the bottom. Make sure the lip of the new one is fully seated in the opening (look at it from the top of the boiler and work it into place while apply pressure from below). Once it's properly seated, there should be noticeable drag on the plunger shaft when it is moved inside the seal.15. Reassembly is the reverse of removal.
1/5/2011 4:07:59 PM • Krups XP7225... • 859 views • 0 helpful votes
0helpful
1answer

I am looking for the owners manual for Krups

Try this one to see if this helps you: http://goo.gl/sl72a
2/22/2011 9:54:16 PM • Krups XP7225... • 186 views • 0 helpful votes
0helpful
1answer

Water leaking from the bottom of the XP7225. I

it is a common issue. See the posts for xp7240. The seal within the plunger is worn or dirty or the valve is sticky. Posted both instructions on other posts.
8/13/2010 6:06:13 PM • Krups XP7225... • 1,384 views • 3 helpful votes
0helpful
1answer

Not frothing milk

that means that the steamer is not generating enough pressure steam.

This happens either because there is not enough heat, or if you release the steam when pressure is not enough.

Very common problem with the american maid makers.

bear also in mind that Krups are not the best at frothing milk, and this is also a basic model.

If you want the best capuccino Coffee machine, buy the italian ones, Gaggia, Delonghi, Ariete etc. that are all great at this, or get a bigger Krups as a replacement like the Krups XP405040 that is also good at capuccino
5/9/2009 11:16:44 PM • Krups XP7225... • 1,144 views • 0 helpful votes
0helpful
2answers

Machine Fault Error No 06

It is probably blocked or dirty inside. Try cleaning tablets other wise see the other posts for cleaning the pressure valve inside the machine.
3/9/2009 10:55:16 AM • Krups XP7225... • 1,911 views • 0 helpful votes
0helpful
1answer

XP4020 - n1164

Krups XP 4020 Semi-automatic Espresso Coffee Maker http://www.coffeemachinemanual.com/krups-xp-4020
5/26/2016 6:17:08 AM • Krups XP Coffee... • 122 views • 0 helpful votes
0helpful
1answer

Hello, I have Krups XP-7220. When I try to make a coffee, machine start to ask me for refilling. And this process is endless.

Check the water float in the tank, it is common for them to cease floating sometimes. Krups solution is a new tank, my solution is to jam something plastic underneath it to lift it up so that it activates the sensor. Even if tank is empty it will no longer ask you to fill it up.
2/4/2015 12:47:18 PM • Krups XP Coffee... • 305 views • 0 helpful votes
0helpful
1answer

The frother nozzle makes a bad screeching noise. What am I doing wrong?

I don't think there is a lot you can be doing wrong to cause that apart from maybe something not too well cleaned and creating a restriction for the steam.
2/4/2015 10:32:19 PM • Krups XP Coffee... • 151 views • 0 helpful votes
0helpful
1answer

How do I fix error code 12

That is a very uncommon error code. It is not detecting the ejection switch pulse, it may be just a case of dismantling and cleaning and checking the switch operation. It's all internal so you need to remove the housings.
9/28/2014 8:24:23 PM • Krups XP Coffee... • 1,254 views • 1 helpful votes
0helpful
1answer

How do I disassemble Krups dolce gusto KP5000 machine?

You will need an instruction manual, if you leave your email address I will send it as a PDF file.
10/8/2014 9:52:06 AM • Krups XP Coffee... • 518 views • 0 helpful votes
0helpful
1answer

Error code 06 on Krups xpt 7240

Look for and remedy any internal leaks. If error 6 remains then expect to replace the distributor assembly.
8/20/2014 10:34:47 AM • Krups XP Coffee... • 1,073 views • 0 helpful votes
0helpful
1answer

Coffe maker krups xp5220-water come out of the top of the machine not from the hole

Open the machine up and look for a broken hose or similar.
9/29/2014 8:16:12 PM • Krups XP Coffee... • 213 views • 0 helpful votes
0helpful
1answer

Where can I get replacement for the two grille plates of my Krups Grille system 2002

are they shorted ? see if thermal blown
9/30/2014 3:41:10 AM • Krups XP Coffee... • 58 views • 0 helpful votes
Not finding what you are looking for?
Krups XP7225 Espresso Machine Logo

33 questions posted

Ask a Question

Usually answered in minutes!

Top Krups Coffee Makers & Espresso Machines Experts

Pierre Laplante

Level 3 Expert

2061 Answers

Ross Keen

Level 3 Expert

1365 Answers

eyecam

Level 2 Expert

100 Answers

Are you a Krups Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

XP Krups

  • XP Krups

Most Popular Question

error code oe

  • Coffee Makers & Espresso Machines
Loading...