LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher - Answered Questions & Fixed issues
The 2 metal "clips" that secure the dishwasher to
door gasket possibly bad or another leak. Stop using dishwasher until repaired or you're likely to ruin your floor. I just had this problem before we found a leak and now we may have to replace the kitchen flooring.
Order new clips or the dishwasher could fall out onto the floor or even onto your foot.
11/16/2017 6:45:28 AM •
LG LDF6920ST...
•
Answered
on Nov 16, 2017
•
222 views
The brackets that came with
Check if there are small plastic plugs on the side of the tub in front. You can insert a screw there under the plug to secure the dishwasher to the cabinet. My LG model has those holes.
10/27/2017 1:01:04 AM •
LG LDF6920ST...
•
Answered
on Oct 27, 2017
•
234 views
Why my dishwasher whistles?
Whistle could be inlet water pump,leak will have to be traced could be from a number of places,poss from pump
9/23/2014 5:24:23 AM •
LG LDF6920ST...
•
Answered
on Sep 23, 2014
•
737 views
Lg dishwasher water not hot
Hot water is introduced into the dishwasher from your regular hot water lines. If you are not getting hot water at your sink, that could be part of the problem. If the water in the machine is warm, you are getting feed from your house boiler, but the instant hot water coils in the dishwasher are not working. There may be a fuse panel for the coils that can be checked or, if not it is a wiring problem to the heat coils or the coils themselves burnt out.
12/28/2012 3:06:27 AM •
LG LDF6920ST...
•
Answered
on Dec 28, 2012
•
220 views
Ldf6920st LG dishwasher. Pump runs continuously.
Continuous run of DW "drain pump" is common problem, with simple solution, and without "pulling" the DW! Because the problem is likely a "stuck float riser assembly", a mechanical "glitch", from crud build up, I recommend trying one "might get lucky fix" first. Look up above the door and remove (usually two) screws holding two metal "tabs" to bottom of wood counter. This should allow you to "rock" the unit a little. This might allow the float assembly to operate. A. You have removed and cleaned the screens to the pump inlet and have manually added hot water which the pump removes but the pump just continues to run, even when you open the door? You should still be able to use controls to shut unit off. If not, you should be able to turn DW off at circuit breaker panel. Find and open the breaker any how, because "I'm sending you in!" There are two sheet metal "plates" about 4 inches high, 24 inches wide below the door on Bosch (and others) dish washers. Remove both, usually they can just be carefully removed. Lay with face on floor and use flashlight to look "up and into" the left bottom side of the DW. About a foot into the bottom left side of the unit look for a red or orange (usually) plastic rod about the size of a pencil rising vertically out of a thin plastic "tank". This is a "sump" of some sort (???) and the bottom of the rod is a "float". The top of the "pencil" activates a micro switch. Junk in "tank" or on micro switch stops rise of the rod which keeps pump running. Carefully, manually lift the orange rod with a long wooden spoon. Several times. You should hear the micro switch click. Don't be sticking screwdrivers or anything metal in there. Even with the power off. Turn breaker back on. This may solve most common problem in first five years for many brands of dish washers. Good luck."Born 33 RPM - now GHz"
12/24/2012 5:50:11 AM •
LG LDF6920ST...
•
Answered
on Dec 24, 2012
•
5,302 views
My dishes come out with a gritty sand all over them.
If you live in an area with hard water, the grit is probably hard water
deposits. Dishwasher detergents no longer contain phosphate, so the detergents often leave behind hard water deposits on your dishes. There is a great solution at
www.cloudydishes.com
11/16/2012 3:34:29 AM •
LG LDF6920ST...
•
Answered
on Nov 16, 2012
•
1,105 views
How do I remove the screw holding the impeller to the drain motor?
(old question but might help someone in future)How to take screw of dish washer impeller:Impeller heats up when the heater at the bottom runs... so maybe impeller melts a bit and sticks on the screw.Heat
up the impeller with a hairdryer for 5 min and try rotating the screw
both sides! (this will soften the impeller a little bit so screw can can
rotate and come out easily!.Hold the impeller (somehow); using a nail, some special tool or inserting a screw driver to the side of the impeller.Unscrew it!I
was trying to take the screw(1SZZED3006A) of the impeller(5911ED3003A)
(motor 4681ED1004B) from LG LDS4821ST and had no idea that they put
REVERSE THREADED screws in these things, ended up melting the impeller
with a torch and then figured that it was a REVERSE THREADED screw!. Note: I wasted
$65 on repair guy who came in and said "you need the sump assembly,
recirculation motor, motor assembly" and gave a $368+tax estimate.
He didn't even check anything just saw a broken part that I already new. I didn't fix the part myself because I wasn't able to take out the screw at first attempt. This time I took the whole sump assembly out thinking I could use more strength this way but the problem was totally unthinkable at that time.Happy fixing!
7/25/2012 3:44:25 PM •
LG LDF6920ST...
•
Answered
on Jul 25, 2012
•
415 views
Our 14 month old dishwasher will not turn on
if you are getting no lights on the display and assuming you have mains power getting into the dishwasher, the problem could be on the power control board located at the top part of the door module under the display panel.Refer the
control panel diagram item K253You have to be careful when handling the dishwasher. Make sure it is disconnected from the main power and the water inlet is turned off. If in doubt call the service technician. You are still covered by parts warranty for 2-5 years (depending on part) See warranty policy in operators manual
7/18/2012 6:41:11 AM •
LG LDF6920ST...
•
Answered
on Jul 18, 2012
•
340 views
We installed our new LG
Hello, ks
I was trying to help
you out here. I was going back to some customers that asked questions
in the past and it appeared that no one answered them, so I thought I
would take some of my personal time to see if I can help. Even though
this site may not have your exact model or brand, This link will help
you tons. Here is a link
to about everything you want to know about your dishwasher, from repair
to trouble shooting it,pictures, video's. Just scroll around and you
will see tons of information to almost any question you might have on
your dishwasher. If you go to this link and click around, I am sure you
will find out so much about your dishwasher, you will know more that the
company that made it. Here Is the link for you to click on>>
http://home.howstuffworks.com/dishwasher.htm
Please if this helped you at all, if you can find the time
to rate my help and some kind words written would be appreciated for my
free help , I would appreciate it. Here is also my direct link to my own
pages of other areas of my expertise for other problems you might have
in Automotive,Appliance, and Electronics. Drop In anytime for my help.
Thanks,Mike
http://beta.fixya.com/users/mc1bean
10/27/2011 9:22:48 PM •
LG LDF6920ST...
•
Answered
on Oct 27, 2011
•
316 views
My dishwasher isn't washing the
make sure the lower spray arm is free from objects in the ports and spins freely. If you still have a problem LG is offering some customers an pump upgrade free of charge depending on the age of you dishwasher
9/2/2011 2:45:19 AM •
LG LDF6920ST...
•
Answered
on Sep 02, 2011
•
452 views
My dishwasher will not empty
You should pull the unit out of the cavity and check the inlet to the drain pump. Sometimes a label or something will get sucked into the inlet and block it. If you don't find a blockage then either your drain pump is bad or the water level sensor is bad.
8/17/2011 3:39:42 PM •
LG LDF6920ST...
•
Answered
on Aug 17, 2011
•
159 views
I am getting a E1 error within the first 10
Hi
E1 is a leakage error in your LG dishwasher; it is usually
displayed either due to a clogged drain or due to water leakage in hose
connections. If the drain pump assembly is not clogged then check the motor
water seal leakage of sump assembly and also check the impeller of washing
pump, if it is worn then replace the impeller. You can also make sure that the
height of drain hose is not over 20". Hope this helps...please post back for
further assistance.
Daniel
8/11/2011 12:16:50 PM •
LG LDF6920ST...
•
Answered
on Aug 11, 2011
•
1,124 views
Not finding what you are looking for?