20 Most Recent Danby DDW497W 22 in. Countertop Dishwasher - Page 2 Questions & Answers

The noise with the poor wash or spin is due to possible CLOGGING of the water line to the pressure pump. So it has to be confirmed that the pump receive good flow of water.
Now clean the inlet filter and the sump filters. make sure that the pump also is not clogged to reduce pressure. Remove the spraying arm and clean them , if possible use a descaling , cleaning operation to clean all ports on the machine.
please check the link for some tips:
http://www.espares.co.uk/advice/dishwashers/a/3/1353/dishwasher-cleaning-properly.html

hello,

what this mean is an indication of a problem detected b the sensor

Some models of washers come with a digital readout display that informs the operator of the unit's function and any errors.

Error codes indicate that a problem has occurred and should be addressed. Different models of washers may vary in their fault displays.

Some washer models use flashing lights at the unit's start, door lock, wash, rinse, final spin and control indicators to display error codes.

thanks

Hello & Welcome to FixYa

The problem seems to be with the float switch assembly that is bad and needs replacement. However, before replacing this part you can run a empty cycle with 3 cups of vinegar inside at its hottest temperature, after this clean the drain filter assembly. If the problem returns then replacing the float switch assembly is recommended repair. Please get back to me if you have any other questions.

Kevin

Hi and welcome to FixYa, I am Kelly.

Since this a brand new unit you should be in direct contact with the manufacturer here:

If you are unable to effect repairs yourself.

Please call our CUSTOMER HELP LINE

"1 800 26 DANBY"
and ask for assistance.

What I wil ask you to do is look for any tape or packing material in the bottom of the unit. If there is any tape on the float or flood sensors it will give you an error.

I note that there is no mention of P2 errors in the user's manual here:
http://ec1.images-amazon.com/media/i3d/01/A/man-migrate/MANUAL000069317.pdf

Thanks for choosing FixYa,
Kelly

Hi,

The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.

Here is a tip that will help you to solve the problem of films, residue, and scum in your dishwasher.

Dishwasher Residue and Film on Dishes

heatman101

/;/;/;/;/;/;/;/;/;/;/;/;/;/;

On mine I discovered that the door latch was bent and wouldn't activate the door switch, so I just bent it down enough to activate it.

Hope this helps!

J

Hi,

I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and installed them in minutes...now the thing works like new... However I have also found that if the heating element goes bad then that also can mess things up bad... So I would buy new spray arms, and also check out the heating element to make sure it is working... Here is a tip that will help you with the online buying...

Dishwasher Spray Arms not Spinning

How to Buy Appliance Parts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The Heating Element not Working

Dishwasher Maintenance

heatman101

Asker's Testimonial "explanation very clear. will give it a go and see how simple it was. thanks Ronnie " - ronnieshomes

sounds like the seal is not sealing properly. check to see if there is any debris along the seal -- or any cracks in the rubber seal.

c...

Order new connector from the manufacturer, the ball bearings cannot be replaced the connector must be replaced as a unit.

I did the same thing when I moved. I went to Home Depot and was able to pick up a replacement nozzle there.

Hello. This is a common item and should be available from any plumbing supply house or appliance store. Call around. J.

Another thing that has worked acceptably well for me in this case is 'gluing' the plastic window back into place with a generous layer of GE Silicone II Kitchen and Bath sealant.

it works on both metal and plastic.

make sure the surfaces are all completely dry and apply a layer around the rectangle area where the plastic would normally meet the stainless steel (remove any plastic bits from the holes so that the sealant can squeeze in a little), place the plastic window back into position and put some weight over the entire surface of the window....not too much, but enough so that it'll squeeze the sealant out to the edges and seal entirely around.

let 'cure' 24 hours

mine has held together over a month now and doesn't appear to be coming apart (although i think i could've used a bit more sealant)

My older model had cheap plastic type rivets around the window. Of course they broke and water leaked out the window. I took the door apart and put in a new gasket the siliconed the heck out of it!
Put dishwasher on a counter or floor and put a nice thick phonebook under neath the opened door for support. Carefully replace window with gasket and a bead of silicone. Put enough weight on top to press it down and seal it. Leave for 24-48 hrs. I've replaced the window 3 times and this fix has lasted 2 years now. total cost about $10 and a little effort. make sure you use heat tolerant silicone.