Hobart AM15T Dishwasher - Answered Questions & Fixed issues

If its only 6months old then contact Hobart for warranty repairs. I'm sure they would be happy to help you as a valued customer

ed = Slow leak. Make sure the drain lever is closed, the standpipe is seated and the o-ring is clear.

E2 = No or slow fill. Water did not reach the float during a fill within 2.5 minutes. Press OFF, wait 5seconds and press. ON. Make sure water suplly valv is open.

I use repair clinic dot com to help me trouble shoot. Have model number and make ready and use their easy to use search. Good Luck.

P2 error is the final rinse probe. Depends on the model of the D/W for location, next to the vac breaker.

Yes I have run into this problem in the field.It is a pain.could the touch pad and the controls on the inside of the door have got wet and it is shorted as to every time it starts it goes into delime cycle and sometimes if it reads an error it will not complete the delime cycle and try to run the cycle again.More of a description would help.Is this d/w old or new does it have a rough life or an easy one does your dish person slop water all over the control panel.

Hobart's website has an online catalogue, if you want to deal directly with the source. You'll need to register with them in order to browse the catalogue, and download service & repair manuals. Otherwise, you can try calling their Customer Service number at 888-4HOBART (888-446-2278).

Alternatively, there are a number of suppliers that sell the equipment and parts. Valiant Equipment in Florida is one of them.

If you bought this piece of equipment new, you might try contacting the vendor from whom you purchased it. (They will probably have stuck a decal on the unit with their name & phone number, hoping to get more of your business.)

bypass it.... its a syphon break.. you dont need it.... 2 pipes in and out of break remove and bridge the 2 ends with 1/2 copper pipe piece

Thanks for your question!

I'm sorry that you haven't received an answer yet.

The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:
1. the question is unclear, incomplete, or poorly worded...
2. the question is mis-categorized - so the correct experts aren't viewing it...
3. the question requires an answer for something that cannot be explained online adequately...
4. specific training, tools, or equipment are required to avoid injury or death...
5. the Experts that are online simply don't have the resources to answer your question fully...

Please feel free to re-work your question if you feel one of these may be the reason.
Of course you are not required - but converting your question to a PAID one usually increases the reply rate as well.

Normal rates for FixYa are...
$ 9.99 answer for one question.
$12.99 Live Real-Time online chat or premium e-mail support.
$29.99 Live Real Time phone support
Sometimes FixYa will run specials for unlimited questions via monthly subscription or reduced rates for limited periods.


Consider the savings that can be had when an informed Expert can save you a $100 service call, or a $350 trip to the car dealership.
Your problem solved - guaranteed! Or your money back!!

If you don't want to pay - feel free to re-submit your question so it returns back to the top of the work queue if you still need help.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

Check thte drain hose as it might be clogged at the entry point to the drain if it connected to a garbage disposer.

Due to liabilitiesand business practices, Hobart will not give out service manuals to anyone other than qualified Hobart technicians.
Post a question and perhaps we can help.

Lee,goto your other post and i posted some solutions.Bigg T

check to see if your element is scaled up or your element may be damaged

Question edited for clarity. Error codes should be on the rear label according to the Technical Manual https://www.partstown.ca/modelManual/HOB-AM15T_spm.pdf There is no E1 error code for that machine and is is suggested that the display may be faulty. https://www.google.com/search?q=hobart+am15+e1+error+code The only reference to E1 is here, for the AM-16 and an electrical 'type'. https://www.hobart.ca/wp-content/uploads/pdfs/warewash/AM16-BAS-Base-Electric-CF48568.pdf For LXi machines Drain and fill error messages are displayed as E0, E1, E2, E3, E4, E5, E6 or E7. In all cases, the dishwasher will terminate current cycle operations, turn off all heat sources and display the message until the OFF button is pressed. (A power drain will not occur when turned off.) (See Troubleshooting.) If problem persists, contact your local Hobart Service Office Phone Hobart Support. there are no Hobart Techs here, just me as caterer, career long Hobart user and Expert finder of information. Or try JustAnswer dot com. ..

Question edited for clarity. Try 1001 https://www.google.com/search?q=Hobart+lxeh+service+code https://www.google.com/search?q=hobart+lxeh+service+manual ..

To me the Error is telling you Probe Error - Wash - Power - Drain CL & CLe Series Dishwasher Display Codes Below are common codes that display on Hobart CL and Cle Series Dishwashers:

• Door(s) Open - This displays if one or both doors are open. Close all inspection doors.
• Clear Conveyor Jam - The code appears if there is a jam. Remove the rack from the machine. Then, press START and rerun the rack.
• Probe Err - TANK - Check if the lower float assembly in the displayed tank isn't visibly damaged and that the proper amount of water is covering the lower float in the tank.
• Probe Error - FnlRns - Make sure the supply water valve to the rinse booster is open.

More here and a video https://www.google.com/search?q=Hobart+PROBE+ERROR-WASH+PW+DR https://www.hobart.com.mx/pdf/FichaTec/F-40196.pdf Service Manual https://hvac-talk.com/vbb/attachment.php?s=219f76d9e796c2e5f1c5fef6b79fad9d&attachmentid=830275&d=1639784925 from here https://hvac-talk.com/vbb/threads/2234701-Hobart-Service-Manuals ..

Question edited for clarity and written English. It is a professional machine, you have it serviced professionally by your local Hobart Service Centre and claim the repair against your expenses. The machines are way beyond the capabilities of someone that can just buy parts online. It is either incorrectly wired or the control board or relays are are failing / failed.

Probably the temperature sensor, but do you want to risk $227 on a guess? It is a commercial machine, just call your local service tech. https://www.google.com/search?q=hobart+dishwasher+ft1000+service+manual+pd It is NOT a common fault https://www.google.com/search?q=hobart+dishwasher+ft1000+rinse+temperature+blank ..

1.Loss of water pressure due to pump obstruction. Check for any obstruction at the pump intake. 2.Strainers clogged causing inadequate water supply to pump. 3.something may be inhibiting free movement of the low water float; remove any foreign object from around the low water float or its magnet.