Top 20 Cuisinart Private Reserve CWC-900 Wine Cooler Questions & Answers

im a union electrician i would contact a company like graybar electrical supply or granger.com

If the light is on and no fan or compressor is running then its your thermostat that is bad. That's the only thing that turns on those parts. As you said the unit is new you should contact your dealer either to replace it.

Keep us updated.

I have a Cuisinart Model CWC900 wine cooler that stopped cooling -- the cooling module is bad.

The FIX.

1. First remove the filler plugs from the screw access holes. I did this by tapping the plug off center with a small screwdriver and a small hammer. The plugs popped right out.

2. Use a #10 Torx driver to remove the screws from the holes.

3. The chip on my cooler was a TEC1-12708 made by HB. The part # was on the chip. I found the chip information by doing a Google search on the part #.

4. I found a replacement chip from Custom Thermoelectric. The part # to replace the chip in my cooler was P/N 12711-5L31-09CQ. Cost is about $20. You should specify that the chips that you order should be 'Sealed'. The lady that I spoke with said that the chips last about two years. The people at Thermoelectric were very helpful and appeared to be very knowledgeable.

5. You should apply heat-sink grease to both sides of the chip before installing the chip.

I hope that this helps.

WGD

You'll have to drill out the little plastic tabs which hide the star screws. I used a Dremel and a quick tap on each little tab to make a small hole, then pried out the plug. Then use a star tool (T10) to remove screws. The fans get dusty and sieze up. Lousy assembly to keep clean, but will be easier now. I had to replace the larger fan.

CONTACT COMPANY : DENVER BETA 303-431-7161 MODEL # YW06010012SL ONE MONTH LEAD TIME... THIS IS A SLEEVE BEARING MODEL THEY HAVE A BALL BEARING MODEL THAT SHOULD WORK ITS GIVEN MODEL IS YW06010012BL REPLACES DFC601012L

based on my personal experience it may be a bad fan. can you feel the fan running? or does it just feel hot near the vents?

you should see if theres a DC voltage going to the plate or not. it should noticeably heat up instantly with proper voltage applied. if power is there and it doesnt heat then the thermoelectric device needs to be replaced. also you should be able to measure a resistance of the plate. Should not be shorted or open. it should be a relatively low resistance. like a few ohms. and it may read different depending on which direction you connect the leads.

Check the airflow in the unit, poor airflow because of a faulty fan or blockage will result in poor cooling. You may want to try defrosting the unit. Let me know what you find when checking it out.


Benjamin

Here is the breakdown on this machine by temperature - it only works optimally in a room that is 68-70 degrees, which is a little on the cold side:

to actually reach 7 degrees Celsius, the room temp must be 68 degrees Farenheit or below
to reach 9 C, room must be 70 F or below
to reach 11 C, room must be 72 F or below
ETC...

all problems with this wine cellar will be aggravated during the summer months

The best thing you can do is turn to a company that provides event rentals. I have worked in the industry for years and have always found that renting is easier than buying. Buying means storing the stuff, keeping it in good condition, and ensuring it always matches your event's theme. With an event company in London, you can choose what you need as each event requires. Some great choices for a company can help you get your hands on the furniture you need, including Velvet Living. Leave the buying to the event companies; you can just rent what you require, so you never have to worry about storing the equipment or adjusting themes and event settings to suit your available furniture.

Check out the link. CDA sell spares direct, plus other vendors. You can also make your own. https://www.google.com/search?q=replacement+door+seal+for+my+CDA+Wine+cooler+model+FWC602SS ..

The tags on the chairs will not be the set model number. I can tell from the sellers that this a brand from China with no stated maker. Try Wayfair for parts, and send them pictures. https://www.google.com/search?q=Mainstay+Bristol+Springs+Patio+set https://www.google.com/search?q=Mainstays+Bristol+Springs+Patio+set+MS17 or here

YOTRIO CUSTOMER CARE

Yotrio https://yotrioint.com > uploads > 2020/04 PDF Before returning to your retailer, call our customer service department at (866) 905-4107, 8:30 a.m. - 5:00 p.m. PST /11:30 a.m.- 8:00 p.m., EST, Monday- Friday ... ..

Question edited for clarity. Back right hand side. Page 8 of the manual

RMS-10

Abt https://content.abt.com > documents > RMS10_om PDF Robotic Massage® Chair ... The warranty applies only to the massage chair; accessories or enhancements are not covered. ... Get-A-Way "Elite" allows you to select ... 12 pages

Touch the button to turn the light on, press and hold to 4 seconds. display from Celcius to Fahrenheit. Touch once to turn the interior light on or off. To switch between Celcius and Fahrenheit, hold button for 4 seconds.

DELUXE WINE CELLAR

According to my notes, it is a failure of the defrosting sensor.Probably best to call a refrigeration engineer.

Question edited for clarity. Normally the standby light on the remote will be on whilst it is plugged into the mains. https://www.google.com/search?q=catnapper+recliner+Should+the+light+on+the+recliner+remote+go+out+or+stay+on ..

Here is the maker / reseller

Recliners

Jackson Catnapper https://www.catnapper.com > Products > Recliners Recliners ; Anders. Group 4789 ; Benny. Group 4105 ; Berman. Group 4738 ; Bingham. Group 4211 ; Brody. Group 4774. ‎Refresher Group 4108 Details · ‎Reliever Group 4795 Details Parts resellers on Wayfair, eBay and Amazon https://www.google.com/search?q=catnapper+recliner+parts& ..

Troubleshooting Error codes An icon or error code will appear on the LCD screen if any of the following happen: The cover of the Safety Release Knob is open. Close the cover and the footrest massage will resume. The footrest massage unit is not in operation position or retract position. Extend the footrest massage unit by pressing the recline button and the footrest massage function will resume. LCD returns to 'Main Menu' The backrest bottom panel is being depressed by some obstacle. Remove the obstacle and re-start the program. Error 15 mean it has overheated.

Yes it is. It is a natural material, breathes naturally and is capable of being kept clean.