20 Most Recent Xterra Fitness Xterra FS320e Elliptical Trainer - Page 6 Questions & Answers

Parts suppliers in the link. This is not a North American brand. https://www.google.com/search?q=Aerofit+AF-737+TREADMILL+replacement+parts ..

It will be the same procedure as replacing the belt. They usually has a mechanism for tensioning the belt. That needs slackening off first. You could contact a seller, or watch the videos

Total Gym CycloTrainer for intese Cardio Workout

Total Gym Direct https://totalgymdirect.com > shop > total-gym-cyclotra... Easy Low-Impact Workout - simply lay back and cycle with the glideboard anchored at the bottom of the rails. Strengthen your core; .. US$399.95 · ‎In stock

• Total Gym CycloTrainer for intese Cardio Workout

  https://totalgymdirect.com > shop > total-gym-cyclotra... Boost your cardio workout with Cyclo Trainer for Total Gym! ... shavings from a rubber belt (presumably a belt that is used to increase the resistance?)

Amazon has them https://www.google.com/search?q=V-Max+MPE+Fitness+6380R+AC+Adapter ..

Here is there Support. Contact is at the bottom of the page.

Technogym Customer Support

Technogym https://support.technogym.com Technogym Customer Support is where you will find all the answers to your frequently asked questions, articles and useful resources to help you to get the ... I also found this A message stating 'the equipment is blocked' essentially means that a problem was detected that *might* be a blockage against moving of the moving parts. This commonly can be owing to two things: 1. the upper and lower assemblies (i.e the upper is the console, the lower is the electronics or boards in the lower part of the treadmill, e.g. the motor controller board and brake board) have a fault in the communication between them. This indicates first that you need to check the cable between console and lower assemblies, and also to re-seat either end, or at minimum make sure there is no breakage or crimping in that cable or wire harness, between console and lower assembly and lower boards. or 2. the error was detected by the brake board, and one must go through the error procedure for a brake board error. (In some models, (2) requires accessing the Low Kit Menu, to see whether there is a genuine error registered in the Low Kit Fault area of memory.) Also 3. you might unplug it from power while it is On, and see how that works, after about 2 hours unplugged, please. ..

limited info generic answer check motor and bearings for failing

In the link https://www.google.com/search?q=mosfet+IRFP+250N+IR+710P+4A+K9 ..

ck here.... https://www.manualslib.com/manual/907061/Technogym-Runrace.html?page=79 Best to you

It is a known issue with this unit. https://www.reddit.com/r/running/comments/i2ai1u/domyos_run_100_error_4_help/ https://www.google.com/search?q=Domyos+T900A+error+codes+E04

Hi, your machine might need maintenance. You can reach out to a Hobart service agent to get this maintenance done. I didn't see any error code associated with "missing link", you might check your device manual for this before calling the agent. Thank you.

https://www.google.com/search?q=stex+8020u+manual ..

The Laptop charger is giving reverse polarity. Use the correct charger for that machine (whatever it is). 'make model (what it is) in every question, first 3 words please. Google make model replacement charger https://www.google.com/search?q=%E2%80%8Bmake+model+replacement+charger ..

It's possible that the alternator is the issue, but there could be other causes as well. It's also possible that the problem is with the console or the wiring. Here are some steps you can take to troubleshoot the problem:

1. Check the console: Sometimes, the console can cause issues with resistance. Make sure that the console is functioning properly and that there are no error messages or other issues.
2. Check the wiring: Make sure that all the wiring is properly connected and that there are no loose connections or damaged wires.
3. Check the alternator: If you suspect that the alternator is the issue, you can test it using a multimeter. If the alternator is faulty, it will need to be replaced.
4. Check the power supply: If the machine is not getting enough power, it can cause issues with resistance. Make sure that the power supply is working properly and that the machine is receiving the correct amount of power.

If you're unsure about how to perform any of these steps, it may be best to contact a professional technician for assistance.

There could be something wrong with the belt or the motor or with the speed controls.

There could be several reasons why your treadmill is stopping after running for only a few seconds. Here are a few things you can check:

1. Power source: Make sure your treadmill is properly plugged in and that the power outlet is working.
2. Safety key: Ensure that the safety key is in place and fully inserted into the console. If the safety key is not properly inserted, the treadmill will not function.
3. Motor: If the motor is not working properly, the treadmill may stop after running for only a few seconds. Check the motor by turning the treadmill on and listening for any unusual noises.
4. Belt: A loose or worn-out belt can cause the treadmill to stop running. Check the belt tension and replace the belt if necessary.
5. Control board: If the control board is malfunctioning, it can cause the treadmill to stop running. Check the control board for any signs of damage or wear.

If you are unable to diagnose the issue, it may be best to contact a professional to come and take a look at your treadmill.

I think that the best place to buy an exercise ball is from Amazon. It will save you some time and money and they will deliver it to your house. I've added a link to make it easier for you http://www.amazon.com/lm/R2CC0J8WY9HU0O/?tag=ball-exercises-20