20 Most Recent magicJack Plus - Page 5 Questions & Answers


Canon Pixma Mp258 Error Code and Possible Solution

P02 (Carriage error)
1.Make sure no foreign material stuck to the print head railway.
2.Clean and check the print head encoder strip cable (timing **** film or encoder strip is a white line on the back of the box set of ink lines may be missing or mess up the ink.P03 (Line feed error): an error in transmission line entering the line feed (LF) is a signal telling the printer to move to another line or a whole new line that would not otherwise have reached the end of the line.
1.Check wire print head position (timing **** disk film) on the side of the machine.
2.Check PCB logic board.
P05 (ASF sensor error) sensor for paper feed error.
1.Try to replace the following:
•ASF / PE sensor unit.
•Drive unit.
•PCB logic board.
P06 (Internal temperature error): caused by abnormal heat inside the printer.
P07 (Ink absorber full): the Ink Wastepad (sponge) inside the printer is full
1.Replace the wastepad inside the printer or install waste ink bin outside the printer
2.then Reset counter protection.
P08 (Print head temperature rise error): caused by thermal print head temperature exceeds a threshold.
1.Replace the new cartridge print head and / or change a new logic board.
P09 (EEPROM error): caused by corrupted or defective EEPROM chips of the printer.
1.Replace the logic board.
P15 (USB VBUS over current): caused by too much current, try removing the USB cable and then plugin again, if solve the error, try to replace with a new USB cable. If the error still exist replace the logic board.
P20 (Other hardware error): The failure of other hardware.
1.Try to replace the logic board.
P22 (Scanner error): a scanner malfunction.
1.try to change the scanner unit or change a the logic board.
E13 or E16: Ink has run out

1.Pressing the Stop / Reset button for 5 to 8 seconds until the led screen display number 1.
E04, E05, E14 or E15: Cartridge may not be installed properly
1.Reinstall the ink cartridge.

Office Equipment... | Answered on May 08, 2020


To do that please follow the steps below:
  1. Open Control Panel.
  2. Select Hardware and Printers option.
  3. Right click on the Network printer (your printer).
  4. Choose Properties.
  5. Go to the Ports tab and choose Configure.
  6. Uncheck SNMP Status Enable option.
  7. Restart the computer and check if the issue persists.
https://answers.microsoft.com/en-us/windows/forum/windows8_1-hardware/getting-error-0x803c010b-while-runing-printer/aed7c762-ee91-4413-a311-e7e0bff1dfe8

Office Equipment... | Answered on May 08, 2020


Hi cinlytan,

With the error that you're getting with your Canon mp258 , error number 6000 this means that your printer needs to be reset. You will need a software resetter for this specific printer. You may also use the software resetter for its many other errors. Kindly click on this link for the instruction and for you to be able to download the service tool. This should fix the error code that you're getting and other issues with your printer.

Hope it helps.

Thank you for using Fixya.

Office Equipment... | Answered on May 08, 2020


Showing results for unlock keys on hitachi projector
Search instead for unlock keys on hatachi projector
Search Results Web results

Hiding The Image; Locking Control Keys; Freezing The Image ...

www.manualslib.com > ... > CP-DX250 guide > User manual
Hitachi CP-DX250 Manual Online: Hiding The Image, Locking Control Keys, Freezing The ... Press Any Key On The Projector Or Remote Control To Restore... ... Keys on the remote control are still functional when panel key lock is enabled.
People also ask How do you unlock a projector button?



How do I connect my Hitachi projector?



How do I release the control panel lock on my Epson projector?



What is frame lock in projector?



Feedback Web results

Hitachi Projector CP-X260 how the unlock the key lock ...

office.manualsonline.com > ... > Hitachi Support > Projector Support
Question About Hitachi Projector CP-X260. how the unlock the key lock... how the unlock the key lock. Asked by hrushikeshmule15 on 01/15/2015 1 Answer.

Key lock on screen cpx1 hitachi projector how to relete key ...

www.fixya.com > ... > Office Equipment & Supplies > Sharper Image
Feb 24, 2012 - Turn the projector on and leave in standby mode. To do this press the power on button for 10 seconds until the projector comes on. To unlock the ...

Office Equipment... | Answered on May 07, 2020


I think that when pink and blue are mixed with each other they make the colour light purple then.

Office Equipment... | Answered on May 07, 2020


check with videojets website. i suspect it needs to be serviced

Office Equipment... | Answered on May 06, 2020


Canon Printer Error B200 usually relates to a printhead problem and an error message code B200 will flash on the Screen. Orange and green lights will keep on flashing 10 times as a sign of this error. Caused by some foreign trash inside the rollers of a printer or due to paper jam in Printer.

Canon Printer Error b200 is a very annoying error. If you are facing the same error check this blog and Just follow the steps which are written on the blog to fix the Canon Printer Error b200. We give online help for Any problem in Canon Printer Errors.

Check this Blog for a full answer- https://www.printererrorsupport.com/blog/canon-printer-error-b200/

printer-support-3-undefined-undefined-0_1.jpg

Office Equipment... | Answered on May 06, 2020


sad thing about these is the have a plastic gear that no one makes as replacement. and they are throw away items unless you know some one hat can machine a brass one the same size . might cost more than a new throw away would

Office Equipment... | Answered on May 05, 2020


https://www.xerox.com/en-us/small-business/insights/printing-problems-and-solutions

Office Equipment... | Answered on May 05, 2020


ON WHAT WE HAVE NO CRYSTAL BALL TO SEE IT WITH

Office Equipment... | Answered on May 04, 2020


Hi there is the solution how to reset Advent AWP 10 printer cartridges, they has a small chip at the front, it has 2 contacts, there is small carbon line between them 2 contacts, all you have to do is to cut or scratch that line with something sharp to brake the circuit, and job is done you can use refill the cartridge forever. It will show always full of ink. Hope this will be helpfull

Office Equipment... | Answered on May 03, 2020


https://www.youtube.com/watch?v=tO-k1Se9S04

Office Equipment... | Answered on May 03, 2020


https://www.allclaveparts.com/m9-m11-error-codes-older-units/error-code-e005/error-code-e005
Error E005 is displayed when the system detects an error with the temperature switch(s) for the heating element relating to the temptronic system. This can include a faulty switch, heating element, or temptronic board. If the cause of the error is determined to be the element or switch you will need to schedule service for the unit as these components cannot be accessed without significant disassembly of the unit. Please consult your local JK distributor to schedule service for the unit.
T

Office Equipment... | Answered on May 03, 2020


Might be.

Office Equipment... | Answered on May 03, 2020


1, This issue occurs due to the jams that are stuck on the Printhead. If you are facing any issue even after removing the paper jam and cleaning the ink cartridge, some missed out or bits of paper may be stuck on the printhead.
2, Before cleaning the printhead try turning Off your printer overnight and try printing. If the issue dosen't get resolved, then go further with the printhead cleaning. Make sure you have the appropriate printhead cleaning software.
3, During the process of cleaning the printhead, it uses ink or in other words the ink may be wasted. So attempt the cleaning process only if the print quality is not good.
4, Ensure that you have loaded the correct size papers. Now tap the Maintenance tab and then the Head Cleaning button. Follow the instructions that are displayed onscreen and wait until the printhead cleaning progress is complete.
5, During the printhead cleaning process, do not turn Off your printer. After the completion of cleaning select the option Print Nozzle Check Pattern, which will notify you about the completion of the printhead.
For more printer related queries get in touch with our experts by just giving a call @ 1-866-293-9220.

Office Equipment... | Answered on May 01, 2020


When the red light is flashing while connected to the charger means the battery is being charged, once fully charged the light turn from red to green without flashing. If the red light is flashing while being use means the battery is low and in need of charging.

Office Equipment... | Answered on Apr 30, 2020


Follow the procedure below to send the scanned data as an e-mail from the computer.
  1. Make sure printer is turned on.
  2. Flick HOME screen and tap Scan. ...
  3. Tap Attach to E-mail.
  4. Tap E-mail from PC.
  5. Tap computer to forward scanned data. ...
  6. Specify settings as necessary. ...
  7. Load original document on platen glass or in ADF.
https://support.usa.canon.com/kb/index?page=content&id=ART169568&actp=RSS

Office Equipment... | Answered on Apr 28, 2020

Tip

RayMing - Professional PCB pcba manufacturer www.raypcb.com


RayMing Technology Co.,LTD . was formed since 2006 where stationed at the Southern of Mainland China (Guangdong). Our Aim is to provide a high calibrated services and supporting for all kind of Printed Circuit Board related business such as PCBA or directly to end customers.
Our products range is starting from double-layer to high end multi-layer PCB in which covered varieties of product categories - Consumer, Telecom, Medical device, Automotive. Surface finishing processes including HAL, OSP, HAL LF, ENIG, Gold Finger, Immersion Silver, Immersion Tin.
Besides our rapid growth of business, "Best Quality" is our global team strategy in order to provide highly 'Precise' and professional servicing for our customers. To achieve this scheme, company placed great effort and attention on quality control system and invested series of quality assurance facilities to satisfy the expectation of our customers. UL, ISO9000, ISO14000 are also certified in order to fulfill our customers requirements and satisfaction.
We will meet our first phrase target 300k square feet production output per month within 2008 and our global production capacity will achieve over 600k square feet on or before 2010 to cooperate with the growth of customers.


Welcome to inquiry and negotiate!
Expect to be your loyal partner!
Thanks for your support and trust!

www.raypcb.com

on Apr 28, 2020 | Office Equipment & Supplies

Not finding what you are looking for?
magicJack Plus Logo

80 questions posted

Ask a Question

Usually answered in minutes!

Top magicJack Office Equipment & Supplies Experts

ray gallant

Level 3 Expert

67926 Answers

C. David Graves

Level 2 Expert

69 Answers

Brad Brown

Level 3 Expert

18342 Answers

Are you a magicJack Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

magicJack Office Equipment & Supplies

  • magicJack Office Equipment & Supplies

Most Popular Question

magicjack lot static line dropping every

  • Office Equipment & Supplies
Loading...