20 Most Recent
- Page 6 Questions & Answers
E07, e08, e02, e15 error
Canon Pixma Mp258 Error Code and Possible Solution
P02 (Carriage error)
1.Make sure no foreign material stuck to the print head railway.
2.Clean and check the print head encoder strip cable (timing **** film or encoder strip is a white line on the back of the box set of ink lines may be missing or mess up the ink.P03 (Line feed error): an error in transmission line entering the line feed (LF) is a signal telling the printer to move to another line or a whole new line that would not otherwise have reached the end of the line.
1.Check wire print head position (timing **** disk film) on the side of the machine.
2.Check PCB logic board.
P05 (ASF sensor error) sensor for paper feed error.
1.Try to replace the following:
•ASF / PE sensor unit.
•PCB logic board.
P06 (Internal temperature error): caused by abnormal heat inside the printer.
P07 (Ink absorber full): the Ink Wastepad (sponge) inside the printer is full
1.Replace the wastepad inside the printer or install waste ink bin outside the printer
2.then Reset counter protection.
P08 (Print head temperature rise error): caused by thermal print head temperature exceeds a threshold.
1.Replace the new cartridge print head and / or change a new logic board.
P09 (EEPROM error): caused by corrupted or defective EEPROM chips of the printer.
1.Replace the logic board.
P15 (USB VBUS over current): caused by too much current, try removing the USB cable and then plugin again, if solve the error, try to replace with a new USB cable. If the error still exist replace the logic board.
P20 (Other hardware error): The failure of other hardware.
1.Try to replace the logic board.
P22 (Scanner error): a scanner malfunction.
1.try to change the scanner unit or change a the logic board.
E13 or E16: Ink has run out
1.Pressing the Stop / Reset button for 5 to 8 seconds until the led screen display number 1.
E04, E05, E14 or E15: Cartridge may not be installed properly
1.Reinstall the ink cartridge.
on May 08, 2020
Can u help me how
With the error that you're getting with your Canon mp258 , error number 6000 this means that your printer needs to be reset
. You will need a software resetter
for this specific printer. You may also use the software resetter for its many other errors. Kindly click on this link
for the instruction and for you to be able to download the service tool. This should fix the error code that you're getting and other issues with your printer.
Hope it helps.
Thank you for using Fixya.
on May 08, 2020
Canon Printer Error B200 usually relates to a printhead problem and an error message code B200 will flash on the Screen. Orange and green lights will keep on flashing 10 times as a sign of this error. Caused by some foreign trash inside the rollers of a printer or due to paper jam in Printer.
Canon Printer Error b200 is a very annoying error. If you are facing the same error check this blog and Just follow the steps which are written on the blog to fix the Canon Printer Error b200. We give online help for Any problem in Canon Printer Errors.
Check this Blog for a full answer- https://www.printererrorsupport.com/blog/canon-printer-error-b200/
on May 06, 2020
Advent printer refill reset
Hi there is the solution how to reset Advent AWP 10 printer cartridges, they has a small chip at the front, it has 2 contacts, there is small carbon line between them 2 contacts, all you have to do is to cut or scratch that line with something sharp to brake the circuit, and job is done you can use refill the cartridge forever. It will show always full of ink. Hope this will be helpfull
on May 03, 2020
Red lights flashing roller not coming on
When the red light is flashing while connected to the charger means the battery is being charged, once fully charged the light turn from red to green without flashing. If the red light is flashing while being use means the battery is low and in need of charging.
on Apr 30, 2020
RayMing - Professional PCB pcba manufacturer www.raypcb.com
RayMing Technology Co.,LTD . was formed since 2006 where stationed at the Southern of Mainland China (Guangdong). Our Aim is to provide a high calibrated services and supporting for all kind of Printed Circuit Board related business such as PCBA or directly to end customers.
Our products range is starting from double-layer to high end multi-layer PCB in which covered varieties of product categories - Consumer, Telecom, Medical device, Automotive. Surface finishing processes including HAL, OSP, HAL LF, ENIG, Gold Finger, Immersion Silver, Immersion Tin.
Besides our rapid growth of business, "Best Quality" is our global team strategy in order to provide highly 'Precise' and professional servicing for our customers. To achieve this scheme, company placed great effort and attention on quality control system and invested series of quality assurance facilities to satisfy the expectation of our customers. UL, ISO9000, ISO14000 are also certified in order to fulfill our customers requirements and satisfaction.
We will meet our first phrase target 300k square feet production output per month within 2008 and our global production capacity will achieve over 600k square feet on or before 2010 to cooperate with the growth of customers.
Welcome to inquiry and negotiate!
Expect to be your loyal partner!
Thanks for your support and trust!
on Apr 28, 2020 | Office Equipment & Supplies
Not finding what you are looking for?