20 Most Recent Euro-Pro Steam Generator EP8001 Iron - Page 2 Questions & Answers

the steam holes is plug.
If you have hard water doposit in the line try some cr7

Cant solve the problem but does anyone know where I can buy a filter in the uk for it or the up todate model no for the filter? please

download from www.fitness.manualsonline.com for free.God bless you

I have a temporary solution that is working: Use WD-40 around the switch. Spray with the straw that comes with the WD-40. Let stand for a couple days, then turn the whole unit upside down and spray again, and let it stand that way for a couple days. If we could get inside, it could be more of a sure thing, but I had given up on mine and when I accidently hit the switch after siting for the last few days, , it came on!

tombowdb

Now for Sears to try to locate the tool that will open the case.

Has found all with detailed operation and with comment that from itself this model.Manual HERE

Sounds like a 'TORX' head.
Does it look like a 'star' inside the screw head? A six-sided star? If so, then it is a TORX head.
Look carefully at it, and determine whether or not there is a small pin sticking out of the center.

The screw you are trying to remove is either a Flat-Head (-), a Philips (+) or a TORX (*).

You can get TORX bits almost anywhere, from the Hardware store, the Auto-parts store, to a Dollar store. You can get them with, or without, the little hole for the pin in the head.

You will probably want to buy a little 'set' that has multiple sizes of bits, and a driver, with an extension for reaching into those deep holes.

call them directly 1-800-798-7398

Try putting a solution of white vinegar and water, 50/50.

Hi,

There is most likely a small port where some particles have clogged.fill reservoir with vinegar and water (50/50) and allow to soak 24 hrs, then reheat then shake vigorously to drain then rinse then retry.
check solenoid steam valve which is fitted on the steam tank output pipe.

post a comment for further assistance.


Thank you for using fixya have a nice day:-)

When bases become slippery it is usually due to a couple of things. Either the unit has been used for so long that it has lost friction which could be a dangerous situation and the other being due to dirt and poor maintenance. If the first happens to be the case then the base needs to be replaced but if on the other hand it is due to maintenance then simply unplug the unit and wash the surface with the use of a wet piece of cloth and soap but ensure the liquid quantity is limited.
Being that you really like the iron if you can get a replacement base would be a lot better because it would just ensure that the iron lasts longer. You can always get iron rests from your local hardware store.
Hope this solution has been helpful?

Hi,

The steam hose of the iron is kinked and broken inside.You have to replace a new one.So it will limit the amount of steam flow.

Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thank you for using fixya have a nice day:-)

Hello,

You will be needing; Vinegar, Distilled water, Old clean thick towel and Toothpick

Clean the hard water deposits out of the spray nozzle on your iron by using a thin, sharp needle. Then, clean the hard water deposits out of the plate vents. Flip your iron upside down. Use a toothpick or two to reach just inside each vent. Clear away any deposits and other accumulations of minerals, starch and other gunk.

Clean the hard water deposits out of the water reservoir of your steam iron. To do this, fill the reservoir with 1 part distilled water and 1 part vinegar. (Distilled water is completely free of minerals so it won't clog your steam iron even further.)
Plug your iron in and set it to a hot "steam" setting. Allow it to heat up for a few minutes. Then, spray the steam and run the iron over the towel. Continue this until the reservoir is empty. The vinegar will dissolve minerals and build-up. Running your iron over the towel will help further clean the vents. If your steam iron still isn't completely unclogged, repeat the process.
Fill the reservoir of your steam iron with only distilled water a few more times. Spray the steam and continue to iron the towel until the reservoir is empty after each fill up. This step will rinse the vinegar out.
Good luck.

Hi,
Checked the shark website for parts and cannot find the part or any parts for your iron...

So I guess your out of luck on this one...
Sorry wish I could give better news...

heatman101

You'll need to get some Calcium, Lime, Rust ( CLR) cleaner. Fill the steam reservoir to full with CLR and turn on the steam function to get the CLR in the system. Unplug Iron and put it in a pan large enough to fit the Iron foot in. Fill pan with CLR until it comes just to the top of the foot and let soak for at least an hour. Empty and refill with Distilled water, then run on steam function and see if that clears out the Calcium deposits. Do this procedure in a well ventilated area as it may stink some. Visually inspect the steam ports for blockage and if there is blockage, clear with a Bamboo skewer or other non - metal probe type object. You may need to repeat this procedure a few times to break up all of the Calcium deposits in the Iron.
You may also want to use compressed air and wrap a rag around the nozzle then insert into the fill port. Blast the air into the Iron to blow the chunky stuff out before doing the above.Hope this helps!!