Top 20 Broan-NuTone N-QT9093WH Combination Heater Heater Kitchen Hood Questions & Answers

If the air flow in the duct is restricted, that can cause excess noise also.

Question edited for clarity. This appears to Broan rather than Braun. Added full model name. This answer on Fixya hints that the original boards were faulty. I thought he was from Broan, but it sounds like he is a repairer. https://www.fixya.com/support/t668741-braun_qs3_range_hood No instructions online, but the board is available https://www.google.com/search?q=broan+qs3+controller+disassembly

Broan Nutone Allure III Range Hood Switch Control Board

Build.ca https://www.build.ca > part > R111653-Broan-Nutone-... Broan Nutone R111653 Switch Control Board. Main Control board switch assembly. Use with QS3 Alllure III Range hood. Product Specifications ... $237.89 Missing: Braun ‎' Must include: Braun

Broan QS3 Allure III Range Hood Parts

Store for Parts https://www.storeforparts.com > Broan > QS3 Part Key Part Number Unit Price 0 SV02544 SV02544?LED 1 SR740013 View 69 more rows Missing: Braun ‎' Must include: Braun

REPLACEMENT PARTS GUIDE

img-b.com https://s1.img-b.com > product_parts > broan PDF Attachment Screws #8-18 x ¼" Type AB or B, 1-Suction Cup. (Rubber Bulb Removal Tool), and 3-Wire Nuts. QS3. Allure III Hood. 97010792 Damper 7" Round -. ..

Question moved from Cameras category. Contact Broan direct for warranty service. https://www.google.com/search?q=Broan+273003 ..

It be just the bulb that needs to be re new

You may need a selector, and/or relay replacement.

Depends what is wrong.To call a repair man will cost a service call before he starts. Check all your wiring and see if there is a short. See what you can do before you call a repairman.

You need to disassemble it to repair it, if you are not comfortable check into either a service person or replacing it.

is it on sleep mode...then it should switch off after sometime...try it

I just replace the whole thing if it has attic access. Have an electrician do it if you are not confident of your skill. Having the light work is not very helpful if the unit is shot. Clean and lubricate the fan shaft on your new one once a year and it will last a long time. You may be able to swap out just the fan if unplugs and it is not riveted in but you will have about the same time and money into it as replacement.

Kitchen Exhaust Fan Custom PM390 Power Pack Module for Wood Range Hoods... halfway down the page you will see some pdf files for: Detailed Specifications - PM390 (PDF) Installation Instructions PM390 (PDF) Detailed Specifications - Liners (PDF

Try this link... Page ten ( 10 )

I dont think they have fuse ...you will have to disconnect from your switch panel

are you sure its water...does it have oil collector along filter... or check for leakage from something from upper floor may be you have washroom or plumbing leakage

I just repaired my k23 with only one speed. I couldn't find any help. I looked at the wiring diagram and saw a couple of resistors that I couldn't find in the unit. Digging a little further I found a huge wire wound power resistor with 4 taps. This resistor tested open. Voila replaced it and all is well. I also changed the small control board for no reason it didn't help.

theres a round clip you have to pry off (its silver but first you remove the the cotter pin looking clip that just slides out)..took me a few to figure it out but its a pain to remove ..use a small flat screwdriver and you will get it off eventually..then when reinstalling you have to press it in while lifting the clip with again a small flat screwdriver.

Sir try to check the starting capacitor and the ac supply feel free to send feed back good day and best regards.

Hi,
Sometimes they can be cleaned and oiled and they will work again...
Cleaning the grease and dust with out ruining the motor is the tricky part...
Take the unit apart as much as possible...spray down the fan part with a degreaser or strong cleaner...let it soak and they spray it down with water to rinse it off...
Then work a few drops of light motor oil into the motor by proping up the fan so that the oil will run down the shaft and into the motor...

then get it running smoothly by working it by hand...

Put it all back together and it should work again...

heatman101

If you are going to use it as ductless then you will not need to buy anything else.

I am a retired career chef, and had this one oven with choking CO in an airport catering kitchen. We had it serviced and it was fixed. It sounds like yours is not getting enough air mixed with the gas. Adjusting the gas is one thing but the venturi to the burners can partially block and unburned gas spills over. Remove the burner and venturi and boil it out in whatever you boil your fryers out with. Are you on mains gas or propane because the jets are different. https://www.google.com/search?q=commercial+oven+emitting+too+much+Carbon+Monoxide ..