Haier 6 Place Sttng Countertop Dshws DCT2500DEWW Kitchen & Housewares - Answered Questions & Fixed issues
Error 1
If your Dishwasher is not Draining check the following PISTON VALVEOn some dishwashers that have a filter (screen) along the back wall of the tub have a piston valve. The piston valve commonly causes dishwashers not to pump out. if your dishwasher does have a filter, remove it. Now remove the piston valve located in the center behind the filter. Now to check the piston valve, press up on the spring. Once done the piston should stop up the hole in the top of the valve. When a piston valve, is bad the piston dissolves to the point that it can no longer stop up the hole, in this case replace it. DRAIN SOLENOIDAnother common problem on some dishwashers that will cause it not to drain properly is the drain solenoid. To check this, first disconnect power from dishwasher then remove the bottom panel of dishwasher. Once off, you should see the drain solenoid attached to the main pump then reach under the dishwasher and push down on the solenoid. If it will not move down it is bad and needs replacing. If it will push, down most of the time it is good but not always so follow these steps as well. Reconnect power to dishwasher, now start the dishwasher in to a cycle. If you have a mechanical timer turn it slowly until the solenoid energizes. If you turn the timer all the way around and the solenoid never energizes replace the solenoid. If you have an electronic control, start the dishwasher and wait a few minutes then push start/reset then the drain solenoid should energizes, if not replace the solenoid. At times the timer will cause this part to go bad especially if its melted or frozen down. So you may have to replace the timer as well. CHECK VALVEIf your dishwasher is not draining properly, the check valve may be your problem. The check valve will be on some dishwashers with both a separatedrain pump and a drain solenoid (note if you do not have both you will not have a check valve). The check valve will be located where the black hose connects to the drain pump. To access the check valve, you must first remove the water from the dishwasher. A Wet-Vac works well. After the water is out, disconnect power to dishwasher. Now remove the dishwasher from under the cabinet. Now remove the black hose (even though you removed the water you will still have water in the pump so be ready).Once off you should see the check valve. It's the little red rubber flap. If it is torn off, the flap may have gone down the drain but you still should see the red ring left behind, in this case replace the valve. Sometimes the check valve will swell up and hang in the pump, if so replace it. DRAIN PUMPIf your dishwasher is not draining properly, the drain pump may be your problem. As stated before, not all dishwashers will have a drain pump. To check this, First check to see if it is getting power. You should have 120 volts when the dishwasher is put into a drain cycle. If you have power and the pump does not run remove the pump and check for obstructions if none found replace the pump.DRAIN HOSEIf your dishwasher is not draining properly, the drain hose may be stopped up. To check, remove all the water from tub. A Wet-Vac works well for this. After the water is gone remove the drain hose (even though you removed the water you will still have water in the pump so be ready) from the house plumbing and the dishwasher. Check for obstructions and remove. If you just installed a new garbage disposal check that the metal knockout was removed. Check the air gap if this is not right your dishwasher will siphon water back into it.
Haier dishwasher XIB6B2S3FS-80 cycle not ending
First thing to try is a reset..
Unplug or turn it off at the breaker for 5 minutes.
You can also try this but it's used to clear error codes....
Simultaneously press and hold Cycle Select and Start pads for 5 seconds.
Press ANY button to complete the reset process. ...
The unit will now be ready to use/function normally at this time.
4/11/2023 2:43:19 PM •
Haier...
•
Answered
on Apr 11, 2023
•
156 views
Haier appliances repair parts search
With 30,000 9.4 out 10 reviews, they must be good!
It won't be the element though, it will the thermistor or the thermostat that is failing. Some can be calibrated. It may also be a failed circulation fan on a fan assisted oven.
Test the oven first with an oven thermometer. elements can be tested for resistance, but in my experience they work or they don't, they don't half work.
https://fixpart.de/de/uber-uns
..
3/11/2023 7:33:05 PM •
Haier...
•
Answered
on Mar 11, 2023
•
30 views
Haier dw9-tfe3 series dishwasher fault
Hi
I got the E6 error at the end of cycle and inside it was exceptionally hot and dry, no leak under DW,
I put breaker off and error was persistent, it finally disappeared after a moment, I guess after temperature went down.
If it happens again I'll update the topic.
7/15/2022 1:49:00 PM •
Haier...
•
Answered
on Jul 15, 2022
•
626 views
My Haier Dishwasher HDW100WHT is pumping water over the floor .The door is firmly closed. Any Suggestions please?
OK. When you see water on the floor, and you open the door, is there any water rising in the wash chamber and breaching the seal? If you open the door and do not see any water other than the water dripping off the dishes or whatever, I would suspect there's a leak underneath. If you see water standing in there, they you will want to clean the food/debris trap. Refer to your manual, if you have one. If the food trap is cleared and the water is still comin out, I would suspect a leak underneath the unit, possibly a loose water hose or drain hose.
4/27/2019 3:03:31 AM •
Haier...
•
Answered
on Apr 27, 2019
•
212 views
We have a Haier dishwasher and the capacitor
Make, model, serial number of your unit is ... ? I have dealt with capacitors for over 50 years, so I know what I'm doing. But there is no such thing as a five MICROVOLT capacitor, which is what 5uv means to a scientist like myself! Did you mean five micro FARAD, which should be expressed 5uF? But the voltage rating is critical, and the physical size is critical and the temperature rating is critical and the lead diameter is critical and the lead spacing is critical and the style (axial lead versus radial lead) is critical.
4/20/2017 3:52:44 PM •
Haier...
•
Answered
on Apr 20, 2017
•
88 views
Not finding what you are looking for?