Top 20
Mint Plus Turbo Charging Cradle Questions & Answers
Mint Plus Turbo Charging Cradle won't function properly
Cradle and contacts are fine. Cradle circuit is nothing but a reed relay and few wires, relay closes on proximity to robot's body, therefore no voltage on contacts before robot is close to cradle.There is a thermistor inside of battery, and mine was bad. I removed it and now I am charging the battery from my bench power supply at about 220 ma current, overnight, and it works. Probably the solution is to get a new replacement battery, but the one with the thermistor inside (OEM), easily recognized by the third wire, and all should be fine, assuming that nothing else is wrong with charging circuit or power adapter (12v/1A)Hope this will give you some ideas of where to poke.Once successful, please post your solution.
How do i fix a vacuum line hose on a car that's been cut?
Alot depends on the type of hose. There are plastic hoses and rubber hoses. Generally you can use a smaller plastic connector to connect two rubber hoses together and visa versa, Make sure it is a snug fix. You could also use an adhesive to keep it together.
3/19/2024 12:09:54 AM •
Vacuums
•
17 views • 0 helpful votes
The steamer is on, but does not produce any steam?
The most likely reasons are
the heating element has failed
or it is blocked with limescale
All question need full 'make model (what is is)' please. Very often specific models have 'history'.
Google
make model no steam
..
12/25/2023 1:24:09 PM •
Vacuums
•
41 views • 0 helpful votes
What kind of thermal fuse do i need for a Haan Si-35R steamer mop ?
Unfortunately, I don't have specific information on the Haan Si-35R steamer mop, including details about its thermal fuse. However, I can provide you with some general guidance on thermal fuses.
A thermal fuse is a safety device that interrupts the flow of electricity in case of overheating. They are typically designed to be non-resettable and need to be replaced if they are triggered. Here are some steps you can take to determine the type of thermal fuse needed for your steamer mop:
1. **Check the Manual:**
Refer to the user manual or any documentation that came with your Haan Si-35R steamer mop. The manual may contain information about the thermal fuse, its specifications, and where to obtain a replacement.
2. **Inspect the Existing Thermal Fuse:**
If the thermal fuse in your steamer mop has blown, you can inspect the fuse itself for any markings or labels that indicate its specifications. Note down any information such as voltage, current, and temperature rating.
3. **Contact the Manufacturer:**
Reach out to Haan customer support or the manufacturer to inquire about the specific thermal fuse needed for your model. They may be able to provide you with the exact specifications or recommend a suitable replacement.
4. **Measure the Fuse:**
If you have the technical expertise and the necessary tools, you can measure the dimensions of the existing thermal fuse and check its electrical specifications. Be cautious and ensure the device is unplugged before attempting any measurements.
5. **Professional Assistance:**
If you're uncertain about the replacement process or lack the technical knowledge, consider seeking assistance from a professional appliance repair service. They may have access to replacement parts and can ensure the correct installation.
When replacing a thermal fuse, it's crucial to use a fuse with the same or equivalent specifications to maintain the safety and proper functioning of the appliance. Using an incorrect or incompatible thermal fuse can pose a safety risk.
Keep in mind that the availability of replacement parts may vary, and it's essential to obtain the correct part for your specific model. Always prioritize safety and, if in doubt, consult with the manufacturer or a qualified technician.
11/19/2023 1:19:15 AM •
Vacuums
•
50 views • 0 helpful votes
How to take off the handle once it is clicked in
I would check the user manual. That said, the following may or may not fit your model: Ensure that the hard floor cleaner is powered off and unplugged to avoid any accidents.
Push a flathead screwdriver into the hole guidance, located at the back towards the bottom of the handle.
The handle can then be released by pulling upwards.
If this does not work, you may need to contact the manufacturer's customer service. Don't be embarrassed about that. Devices are often tricky about assembly and disassembly and offer one very elusive way to come apart or require special tools.
12/1/2023 8:30:49 AM •
Vacuums
•
38 views • 0 helpful votes
My new beldray 12 in 1 steam mop makes a clicking noise when using?
I don't find specific information about this problem. Here are some things to try. If they don't work, you may call beldray customer service. Check the water tank: Ensure that the water tank is filled with enough water and is properly inserted into the mop.
Clean the mop head: Remove the mop head and clean it thoroughly. Dirt or debris on the mop head can cause clicking noises.
Check for blockages: Check for any blockages in the nozzle or steam outlet. You can use a needle or pin to remove any blockages.
Descale the mop: If your mop has not been descaled in a while, it could be causing the clicking noise. You can descale your mop by following the instructions in the user manual.
10/22/2023 1:41:12 PM •
Vacuums
•
87 views • 0 helpful votes
Not finding what you are looking for?