DCS WO-230 Stainless Steel Electric Double Oven - Answered Questions & Fixed issues

Based on the information you provided, it sounds like you have already done a thorough job troubleshooting and attempting to resolve the issue with your DCS Fisher Paykel gas oven. If the oven is not reaching high temperatures even after you have replaced the igniter and dual gas valve, and swapped the circuit board from the working side, there are a few other things you can check:

1. Check the oven thermostat: The thermostat is responsible for regulating the temperature in the oven. If it is not functioning properly, it may be preventing the oven from reaching high temperatures. You can test the thermostat with a multimeter to see if it is functioning correctly.
2. Check the oven temperature sensor: The temperature sensor is located inside the oven and sends temperature readings to the control board. If it is not working properly, it can cause the oven to not heat up to the desired temperature. You can test the sensor with a multimeter to see if it is functioning correctly.
3. Check for obstructions in the gas line: If there is a blockage or obstruction in the gas line, it can prevent the oven from getting enough gas to heat up to high temperatures. Check the gas line for any debris or blockages and clean them out if necessary.
4. Check the regulator: The regulator is responsible for regulating the pressure of the gas going into the oven. If it is not functioning properly, it can prevent the oven from heating up to high temperatures. You can test the regulator with a gas pressure gauge to see if it is functioning correctly.

If none of these solutions solve the problem, it may be best to contact a qualified technician to further diagnose and repair the issue with your oven. They will have access to a service manual and specialized tools needed to diagnose and repair the oven.

260°C or 500°F is hot enough to damage the electrics within the oven. Call an appliance repair service for a repair.

Give them a call tomorrow their very helpful..... https://www.genuineapplianceparts.com/manufacturer/DCS_/41/48

https://www.youtube.com/watch?v=N5tyw4cw0pM

Hi Lou, sounds like you have a bad igniter. If it's not drawing enough amps it won't open the gas safety valve. Fairly simple to replace if you're confident working with electrical parts,if not I'd definitely call a repair company. Hope that helps.

Hi Steve, from what you're describing,it sounds like you've got a bad door lock motor. It should have 2 check switches on the assembly. If one or both of those switches are bad,the control will not read the lock as being engaged so it will not allow the cleaning cycle to start. To get the oven door open you need to pull the locking hook over to the right with a coat hanger. To access the lock assembly you have to get under the top. It's a pain in the rear end but it is doable. Hope that helps and good luck.

I have attached a link to the service manual, there are relays that control the elements. https://www.manualslib.com/manual/703000/Dcs-Wo-227ss.html?page=42#manual

This is a tough question because we haven't mention the make and model number you should add that so we can help you better but normally if the top oven is not working properly it may have thermostat problem or it could also be control panel problem can you tell more information especially the make and model Sometimes you can take it out and it's not working properly and take that oven and put it in self-clean mode and it might fix problems

https://www.searspartsdirect.com/model-number/RGSC305BK/3232/0124002.html You can try this site If you need further help, I’m available over the phone at https://www.6ya.com/expert/daniel_a4640839dbb7ec58

is the control panel locked?i know this isn't your model because you didn't send the model number but maybe this will help you out https://www.fisherpaykel.com/vault/pdfs/pdf_usecares/590700A%20OB30DD%20quickstartA3%20USCA%20(EN)w.pdf also if you used the self clean the lock might have been damaged usually from the extra heat that's used when in self clean,the oven gets up to 1000 degrees and can damage the electronics in any stove or oven.but if you're pressing buttons and they don't seem to work the control lock most likely is on.

hi there. this is all i could find.go to this link and see if it helps you. How to calibrate DCS ovens Google Search

Hello Friends! This dimming vacuum display is either caused by a power supply failure with the control board, or a the filaments of the display themselves have started to wear-- similar to that of a bad light bulb. Either way, FixYourBoard.com can solve this problem- This control board is no longer available to buy new. Contact FixYourBoard.com at 512-355-1108 for more information. The photo below is from a double oven, but they repair single oven displays too.

Good Morning Mr Villa! FixYourBoard has repairs what youre experiencing in 2-3 business days. They'd remanufacture your part, and replace your dimming display, fully test the unit.. and back their work with a 2 year warranty. http://www.fixyourboard.com

hi glen... if the front right burner clicks all the time you will have to replace the ignitor. IF the oven door won't close, check the hinge side to see if there is debris there. If the door is sprung it will have to be replaced. Joe

Thanks for choosing Fixya!

You can get a spring from Airedale Springs - Telephone - 0845 4754201

If the fan is not working you need a new fan, if the fan is working but there is no heat you need a new heating element.

HI. This is the result of the Function key that is shorted or stuck.

This will require you to Replace touch pad, or if touch pad is part of the clock, replace the clock (ERC), or main control board.

Clock = Control board
ERC = Control board.

Error code A03. Replacement: XFT135 XFT135-0D06 2230482. Sensor issues or bad wiring is the usual cause.

Question edited for clarity. Two question amalgamated into one. Duplicate question deleted. Refresh page to see your question. Full 'make model (what it is)' in all questions please. High Temperature Silicone Sealant.

HIGH TEMP 100% RTV Silicone Sealant

Dap.ca https://dap.ca > caulks-sealants > specialty > high-temp Features & Benefits · High temperature formula · Service temp up to 550°F (intermitent) · Ideal for flue pipes & other high temp applications · Shrink & crack ...

DAP HIGH TEMP 100% RTV Silicone Sealant

Home Depot https://www.homedepot.ca > ... > Caulk & Sealants DAP HIGH TEMP SILICONE is a high-performance sealant designed especially for extreme high temperature applications. It provides a long-lasting, ... ..

Question edited for clarity, wrong type of 'made' versus 'maid'. All questions need FULL 'make model (what it is)' please. It appears to be an obscure model GE wall oven? https://www.google.com/search?q=PSB9240SF6SS Turn it off at the breaker and leave it off overnight. In the morning press and hold any button for 2 minutes. This fully dissipates any memory in the control board. The reconnect the power. Not sure who 'Beniam' is? https://www.google.com/search?q=Beniam ..