20 Most Recent
DCS WO-230 Electric Double Oven - Page 3 Questions & Answers
Oo our 48" gas stove
hi glen... if the front right burner clicks all the time you will have to replace the ignitor. IF the oven door won't close, check the hinge side to see if there is debris there. If the door is sprung it will have to be replaced. Joe
Thanks for choosing Fixya!
12/18/2010 1:39:58 AM •
DCS Ovens
•
Answered
on Dec 18, 2010
Bake and convection coils do
Alright, generally this is a sign of the temperature sensor being bad as the broil coil will still work even if the sensor is bad but we can also test the coils. To test the sensor and coils, you need to pull the oven out and remove the back panel. Make sure to unplug the oven. The sensor can be seen inside the oven. It looks like a small thin rod towards the back top of the oven (about 6 inches long). Disconnect both the rod and the element wiring connectors at the back of the oven. Using an ohm meter (you can purchase one cheaply at any electronics store), you can measure the resistance at the terminals of both the sensor and the elements. The sensor resistance should read about 1000 ohms and the elements about 20 ohms at room temperature. If either one is extremely high or infinite, then it is bad and needs to be replaced. Let me know how this works out for you. Benjamin
12/30/2009 10:24:33 PM •
DCS Ovens
•
Answered
on Dec 30, 2009
No 7 &beeping
HI. This is the result of the Function key that is shorted or stuck.
This will require you to Replace touch pad, or if touch pad is part of the clock, replace the clock
(ERC), or main control board.
Clock = Control board
ERC = Control board.
12/16/2009 9:04:35 PM •
DCS Ovens
•
Answered
on Dec 16, 2009
A03 code at unox convection oven
Error code A03.
Replacement: XFT135 XFT135-0D06 2230482.
Sensor issues or bad wiring is the usual cause.
4/8/2024 8:37:24 AM •
Ovens
•
Answered
on Apr 08, 2024
Hi can you provide me with instructions how to change my thermostat on a Defy oven serial number - DGS 158 AA 14 11 100288
To change the thermostat on a Defy oven with the serial number DGS 158 AA 14 11 100288, follow these steps:
- Disconnect the power to the oven by unplugging it from the wall outlet or turning off the circuit breaker that supplies power to the oven.
- Remove the screws that secure the back panel of the oven to the frame. The back panel is typically located at the back of the oven, near the bottom.
- Once the back panel is removed, you will be able to access the thermostat. The thermostat is typically located near the top of the oven and is a small, round component with a knob or lever that controls the temperature.
- Disconnect the wires that are connected to the thermostat. There should be two or three wires connected to the thermostat.
- Remove the thermostat from the oven by loosening the mounting screws that secure it to the frame.
- Install the new thermostat by reversing the above steps. Make sure to connect the wires to the correct terminals on the new thermostat.
- Replace the back panel and secure it with the screws that you removed earlier.
- Restore power to the oven by plugging it back into the wall outlet or turning the circuit breaker back on.
- Test the new thermostat to make sure it is working properly.
Note: These instructions are general guidelines and may vary depending on the specific model of your Defy oven. If you are unsure of how to change the thermostat on your oven, it is recommended that you contact a qualified appliance repair technician for assistance.
3/18/2024 7:51:21 AM •
Ovens
•
Answered
on Mar 18, 2024
We bought a house with
Hi Jacqui and Sven,
Check these guys out...you'll have to call or write, but they should be able to answer any (and all) questions about the Everhot Deluxe 204. They even carry spare parts! Hope this helped.
http://www.woodstoves.com.au/html/everhot_parts.html#Everhot
3/5/2024 6:04:27 AM •
Ovens
•
Answered
on Mar 05, 2024
Racks falling down
I have the same problem with a Kenmore oven. Looks like the oven walls have bent outward.
2/27/2024 12:04:04 AM •
Ovens
•
Answered
on Feb 27, 2024
We have a Whirlpool oven from Ikea. It has fault
Its not always the oven temperature sensor.
can also be a bad circuitboard.
or config figuration.
there is a on youtube someone how to do it.
i had a 20 year old oven with de failcode F 03.
fixt it with the config and it works again.
2/25/2024 6:23:36 PM •
Ovens
•
Answered
on Feb 25, 2024
Whirlpool AKP 202 - - - C error message. What is it?
Hi, you have to switch off the machine for some minutes. After restarting push the "SET" and "OK" together and you will get the service menu, where you have to change "EUR" to "EURN".
If the service menu doesn't activated you have to remove the calbe of display from control unit for some minutes and restart again.
2/19/2024 11:07:48 PM •
Ovens
•
Answered
on Feb 19, 2024
Not finding what you are looking for?