20 Most Recent Rheem RQPMA037JK R410A All-in-One Package Unit Heat Pump - Page 2 Questions & Answers


no it is a straight a/c cooling only unit

Rheem Heating &... | Answered on Mar 10, 2016


check your air handler overflow pan and check to see if it is full of water. If so, you need to unclog the normal drain and remove the water in the overflow pan, once level is low enough the float switch will reset and control power will start unit up again.

Rheem Heating &... | Answered on Feb 11, 2016


This will be dependent on the capacity (tonnage or BTU/Hr) of the condenser, its location and how much refrigerant will be needed to added / replaced - plus the labor to do it. A typical 2 - 3 ton residential system (air handler / condenser - no duct work, etc.) can run $2k and up.

Rheem Heating &... | Answered on Nov 09, 2015


If this is a reasonabley new style furnace it's because your flame sensor, they get tarnished and you have to follow the Orange wire on the left side of the burners that leads to the screw (1/4" hex) that you have to remove before you can remove the sensor. Once you do you will need to clean the sensor (it's just a rod bent to a right angle) use some fine grain sand paper, or Emory cloth, and put it all back together, and there you go.

Rheem Heating &... | Answered on Jan 30, 2015


Check thermostat. Check for a burnt out ignitor.

Rheem Heating &... | Answered on Nov 28, 2014


Need more info

Rheem Heating &... | Answered on Nov 28, 2014


Possible bad motor and/or bad capacitor and/or bad blower relay.

Rheem Heating &... | Answered on Nov 28, 2014


Reset the switch. Check the heat exchanger thoroughly for blockages, cracks or holes. Check induced draft motor for proper operation. Check flue pipe and chimney for obstructions.

Rheem Heating &... | Answered on Nov 28, 2014


Clean the flame sensor.

Rheem Heating &... | Answered on Nov 28, 2014


If it only lights for a few seconds you most likely have a dirty flame sensor. Remove the sensor polish it with some emery cloth or very fine sand paper. reinsert. problem should be solved.

Rheem Heating &... | Answered on Nov 28, 2014


Look at the nameplate data on the blower motor itself. If it is an older motor, you will need the horsepower hp, the rpm, the amp draw, and the size of capacitor. Always change the capacitor when installing a new motor.

If it is a newer motor (ECM) you will most likely have to get a repair guy to get the motor and have it programmed properly at the dealer for your type of air handler.

Rheem Heating &... | Answered on Sep 29, 2014


You will need a 4 in 1 tool and new valve cores sold at most supply houses. It screws onto the service connection and the rod pushes in to unscrew the valve core. Once the core is loose, allow the pressure to push rod out, shut the 90 degree valve and unscrew the push rod, the valve core can easily be changed out for a new one by reversing steps. While your at it, get new valve caps with good orings to replace the old caps.

Rheem Heating &... | Answered on Sep 29, 2014

Not finding what you are looking for?
Rheem RQPMA037JK R410A All-in-One Package Unit Heat Pump Logo

3 questions posted

Ask a Question

Usually answered in minutes!

Top Rheem Heating & Cooling Experts

Lawrence Oravetz

Level 3 Expert

10548 Answers

ray gallant

Level 3 Expert

70868 Answers

 Russ Hill
Russ Hill

Level 3 Expert

4057 Answers

Are you a Rheem Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Rheem Heating & Cooling

  • Rheem Heating & Cooling

Most Popular Question

btu capacity ahr42c3xh21b

  • Heating & Cooling
Loading...