20 Most Recent Intertherm 56000 Btu Gas Furnace Questions & Answers


filters are usually on the inside of front door

Intertherm 56000... | Answered on Dec 18, 2017


Burners could be clogged from previous years of use- turn off pilot-then gas and remove and clean burner then replace and follow your steps backwards then start system

Intertherm 56000... | Answered on Dec 05, 2016


If you are positive the fan is turning and no air flow you have a very dirty filter or all zone dampers are closed (very unlikely because most zone dampers fail in open position).

Intertherm 56000... | Answered on Jan 06, 2016


  • Thermostat calls for heat
  • Venter motor starts
  • Air switch verifies vacuum
  • Igniter sparks, or glows - depending on furnace
  • Flame starts in burner
  • Flame rod senses flame
  • Burner continues to burn until thermostat stops calling for heat
By your description, I would polish your flame rod, it will be a metal rod that is insulated from the bracket that is screwed to the furnace case and it will have a single wire attached to flame rod,

Intertherm 56000... | Answered on Oct 04, 2015


According to the web, the model C7BAM03648CC is a Westinghouse refrigeration unit. Are you sure you didn't get the number from the top portion?

C7BAM Cased Vertical Coil
• R410 refrigerant-non-ozone depleting
• All aluminum micro-channel coil eliminates formicary corrosion
• Piston metering for all 13 SEER matchups
• Field installed TXV accessory for 14 SEER matchups

Recent Intertherm furnaces have "M" or "CMF" numbers.
Either way, you will probably have to contact a local dealer because their website is useless.


Intertherm Gas Furnaces

Intertherm 56000... | Answered on Jun 11, 2015


furnace operation= call for heat- inducer blower motor energizes- pressure switch makes- after a few seconds ignitor activates.
If this series of processes is not whats happening the furnace may be going into a code safety. Call to discuss further=913-557-9111

Intertherm 56000... | Answered on Mar 17, 2015


If you have a programmable thermostat do the batteries need replacing? Test and re-insert. While there check for any loose wires on it, or at the furnace circuit board. Also make sure none of the wires are touching and metal parts and getting chaffed or shorted. If they are the shot will keep the unit from shutting off and/or cause short cycling.

Intertherm 56000... | Answered on Mar 01, 2015


The fan speed might be set to fast cooling the fan limit control prematurely. Or the fan limit switch is not calibrated correctly. Or the fan limit switch is bad.

Intertherm 56000... | Answered on Dec 19, 2014


If your diagnostic indicator is not picking showing a fault code than it thinks everything is ok with the furnace. It could be a bad thermostat. (or the heat anticipator in the thermostat).

Intertherm 56000... | Answered on Dec 19, 2014


Sounds like you fan limit control is not set properly. Or the blower speed is set to high.

Intertherm 56000... | Answered on Dec 19, 2014


Try grounding the circuit board properly.

Intertherm 56000... | Answered on Dec 05, 2014


To convert KW to BTU use the following:
1KW= 3412.142 BTU/ hr

Hope this helps.
Bob

Intertherm 56000... | Answered on Dec 01, 2014


You are going to need a service man. A magnehelic gauge is needed to properly diagnose a pressure switch issue. Could be a blocked or restricted flue, a defective induced draft motor, cracked heat exchanger, restricted secondary heat exchanger, ect. ect.

Intertherm 56000... | Answered on Sep 28, 2014


bad motor and/or capacitor.

Intertherm 56000... | Answered on Sep 13, 2014


Will it initially light, then go out when you release the button?
If yes, then change/adjust the thermocouple or pilot size.
If no, then check that you have a gas supply, that the igniter is sparking, that the gas valve is allowing the pilot flow through.

Intertherm 56000... | Answered on Sep 07, 2014


www.intertherm.net/

Intertherm 56000... | Answered on Aug 03, 2014


Power off, power on. Let know what happens

Intertherm 56000... | Answered on Aug 02, 2014


If the sensor knocks the unit off and the the fan keeps blowing without a flame ,the limit (the sensor is a limit comptroller that turns off flame @ a set temp and allows the fan to run until the heat exchanger cools to @ set temp) has out lived its lifetime and needs to be replaced.the button is a manual reset that once reset would allow the unit to continue to run flame and blower at the same time after having been set once, if it is an ongoing problem and needs to be reset more than once then replace the limit control (sensor) in kind. (With the same mode and set-points for the limits)

Intertherm 56000... | Answered on May 30, 2014


Sounds to me like it is going off on a weak high limit switch. With the fan on it will prolong the event but will not stop it. I would check all of the high limit switches. It would most likely be one close to the heat exchanger.

Intertherm 56000... | Answered on Apr 13, 2014

Intertherm 56000... | Posted on Jan 27, 2014 | Be the first to answer

Not finding what you are looking for?
Intertherm 56000 Btu Gas Furnace Logo

28 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Intertherm P3RA-048K Air Conditioner
Intertherm P3RA-048K Air Conditioner

259 Questions

Intertherm P3RA-036K Air Conditioner
Intertherm P3RA-036K Air Conditioner

59 Questions

Intertherm P3RA-030K Air Conditioner
Intertherm P3RA-030K Air Conditioner

33 Questions

Intertherm P3RA-060K Air Conditioner
Intertherm P3RA-060K Air Conditioner

24 Questions

Intertherm P3RC-030K Air Conditioner
Intertherm P3RC-030K Air Conditioner

32 Questions

Top Intertherm Heating & Cooling Experts

Dennis Boxerman

Level 3 Expert

1305 Answers

john h

Level 3 Expert

23515 Answers

Brad Brown

Level 3 Expert

18563 Answers

Are you an Intertherm Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Intertherm Heating & Cooling

  • Intertherm Heating & Cooling

Most Popular Question

after preheat fan cuts in 10 sec cuts

  • Heating & Cooling
Loading...