Top 20
Craftsman Shop Vac 8 Gallon Replacement Filter Questions & Answers
My shop-vac stopped mid-job with no warning
Maybe it over heated or the hose was jammed. Unplug it for a few minutes, check the hose for any stuck debris, then plug it back in. Shop vacs also come with a filter. If the filter is too dirty, it might have shut off as a safety precaution to not cause a fire. Follow directions to clean the filter. Hope this helped. Dee
My shop vac jsut hums
If the check ball is stuck closing airway, the strike the unit on top when its off, you may hear the ball drop and there try again. Otherwise, if that's not it, most like the fan portion inside to create air movement has separated from shaft of motor assembly. You may try top open top and reconnect, but if you not sure don't try this. Take a look at product info for possible replacement or back to store for advice.
Where is the thermal fuse on my craftsman 5.0 HP shop vac?
I don't know exactly but if it has one it will usually be found in intimate contact with the motor.
Some vacs were fitted with a bimetal breaker which is also sited close to the motor, but sometimes there is so much dust around once they open they fail to make a good contact again when the cool and close.
Older vacs weren't fitted with any safety devices.
11/11/2017 10:55:09 PM •
Craftsman...
•
1,569 views • 0 helpful votes
I have a Craftsman wet
Most wet dry vacs have a ball float that blocks the vacuum when it is full of liquid. Yours sounds as if it is full or the ball has gotten stuck in the up, or blocking position.
7/4/2017 1:06:03 PM •
Craftsman...
•
559 views • 0 helpful votes
I don't want to pay to find out out to use my
Hi, W/D here.
Every so often, people get a bit twisted up about this website, thinking that they have to pay for advise. What it is, is, those things are options, but if you just want to just throw out your question and wait for a response, it's free. And, here we are.
Go to http//www.searspartsdirect.com and enter your model number. This site will have exploded diagrams and parts lists for your vacuum, and will probably have a button link to your manual that you can download (for free!). Enjoy. Thanks for using FixYa, where folks really try to help!
Best regards, --W/D--
4/2/2011 2:08:52 AM •
Craftsman...
•
181 views • 0 helpful votes
I am renting a house
Try jerking the emergency cord the oppisite way to put it back in gear and the door must be up all the way open
3/15/2011 1:20:52 AM •
Craftsman...
•
143 views • 0 helpful votes
Snowblower when running it backfires
THE MOST LOGICAL CAUSE IS THE CARBURATOR NEEDS REBUILT. IT IS DIRTY AND RESTRICTING FUEL AND AIR FLOW. HAVE A GOOD DAY! it may even be as simple as a new spark plug. try turning the fuel adjustment on carb, all the way in and back it out 1-1/2 turns. the idle screw should be screwed all the way in and backed out 1 turn. if it has a screw on bottom of float bowl or carb, it is the high speed jet, try adjusting it, in or out.
11/27/2010 2:10:40 AM •
Craftsman...
•
493 views • 1 helpful votes
T.he light on the garage
Either the bulb blown or not wired right when installed. should have one red wire, one black wire and a ground wire, green or copper.
12/23/2010 8:28:44 PM •
Craftsman...
•
216 views • 0 helpful votes
I have a Craftman 5hp
This sounds like the carburetor needs disassembled and cleaned. This happens over time and the tiny orifices plug up. Usually from letting gas set in them for extended periods of time and it gums up. If you are not familiar with them, I would take it to your nearest small engine repair shop.
1/10/2010 1:15:56 AM •
Craftsman...
•
300 views • 1 helpful votes
Trying to remove motor from wet-dry
Hi Dan:
I am not familiar with this model but some of the consumer wet vac models are build with a module and motor as one part. You will need to replace the entire module
8/8/2009 8:57:29 AM •
Craftsman...
•
327 views • 2 helpful votes
Not finding what you are looking for?