Top 20
Dyson DC40 Multi floor Upright Vacuum Cleaner Questions & Answers
Loss of suction in hose
your hose is blocked get some thing long and thin push it done the hose and try and clear it
Dyson Animal V6 flashing blue and red?
two faults, mainly battery.
A flashing blue light indicates that there is no power, please charge the battery. A flashing amber light indicates that there is no power or a temporary fault (e.g. too hot/cold). A flashing red light indicates that there is a fault, please call the Dyson Helpline.
..
3/19/2024 1:50:29 AM •
Dyson Vacuums
•
18 views • 0 helpful votes
Dyson airwrap hair styler turns off at some heat settings and red light is blinking
If your Dyson Airwrap hair styler is turning off at certain heat settings and the red light is blinking, it could indicate a potential issue with the device. Here are a few troubleshooting steps you can try:
1. Check the power supply: Ensure that the Airwrap is properly plugged into a functioning power outlet and that the power cable is securely connected to the device.
2. Reset the device: Unplug the Airwrap from the power source and wait for about 30 seconds. Then, plug it back in and try turning it on again. This reset may resolve any temporary issues.
3. Clean the filter: The Airwrap has a filter located near the base of the handle. Check if the filter is clogged with dust or debris. If so, gently clean it with a soft brush or by rinsing it under running water. Allow it to dry completely before reinserting it into the device.
4. Check for overheating: The red blinking light on the Airwrap can also indicate that the device has overheated. If this is the case, it may have an automatic shut-off feature to protect against damage. Allow the Airwrap to cool down for a while before using it again. Make sure the vents on the device are clear and not blocked by hair or other obstructions.
5. Contact Dyson support: If the issue persists after trying the above steps, it's recommended to contact Dyson customer support for further assistance. They can provide specific troubleshooting advice or arrange for repairs if necessary.
Remember to refer to the user manual or Dyson's official support channels for the most accurate and up-to-date information regarding your specific model of the Dyson Airwrap hair styler.
6/21/2023 6:51:12 AM •
Dyson Vacuums
•
187 views • 0 helpful votes
What size Torx screwdriver do I need to fix a Dyson V8
You ONLY need a T15 for these models DC01, DC02, DC03, DC04, DC05, DC07, DC08, DC14, DC19 and DC25.
If you are going to be working on models such as the the DC24 and other later Ball machines like the DC15 and DC18, and newer machines like the DC39, DC40 and DC41, not to mention new Cinetic machines, you will also need a T10 with an anti-tamper end and also a T8 for some jobs.
If you are planning to repair later models, get a T8, T10 T and the T15 T (The extra "T" denotes anti-tamper).
1/14/2023 7:25:29 AM •
Dyson Vacuums
•
58 views • 0 helpful votes
My dyson dc25 got over full and just stopped working. It turned on with half power but wouldn't sick anything up and now won't turn on at all. Please help.
Here are a few steps you can try to troubleshoot the problem:
- Check the filter: Make sure that the filter is clean and that there is no blockage in the filter.
- Check the bin: Make sure that the bin is empty and that there is no blockage in the bin.
- Check the brush bar: Make sure that the brush bar is not clogged with hair or debris.
- Check the hose: Make sure that the hose is not clogged or blocked.
- Check the motor: Make sure that the motor is working properly.
- Check the power supply: Make sure that the power supply is working properly and that the vacuum cleaner is properly plugged in.
- Consult the manual: Consult the manual for specific troubleshoot and service information for your Dyson DC25 vacuum cleaner model.
1/13/2023 5:47:47 PM •
Dyson Vacuums
•
42 views • 0 helpful votes
Dyson v11 motor not smooth
Hi,
if the calibration steps (often) recommended by the manufacturer do not work, please switch outlets and monitor performance of the motor from the different power source. If this fails, then you might next swap your current motor with another one from ebay or alixpress and test the vacuum again with the substituted motor.
Thank you.
12/28/2022 12:21:37 AM •
Dyson Vacuums
•
40 views • 0 helpful votes
Why does my Dyson D43 dust canister not snap into place?
I also have a dyson vacuum but it is an old version. I have been having that problem recently and i researched the internet about the similar subject. People are having so many complains about the release button . Hopefully you will solve it by calling the service to replace it with a new dyson. Otherwise the problem you are having will continue
good luck??
12/14/2022 3:46:09 PM •
Dyson Vacuums
•
46 views • 0 helpful votes
Not finding what you are looking for?