Top 20 Dirt Devil UD40270RM Quick Power Compact Bagless Upright Vacuum Refurbished,Lightweight,Fold Down Handle,HEPAFiltration,5 Position Height Adjustment - Page 8 Questions & Answers

Hi! Model M086605 takes a Dirt Devil Type C bag. Follow the link below to purchase the bags from dirtdevil.com. Hope this helps! Search

Hello! We have several Purpose for Pets models. I have included the link to the Purpose For Pets Bagless Upright Vacuum model M140000 instruction manual. If this is not the model you have please reach back out to us and include the model number. Hope this helps! http://bit.ly/1pB8DM1

heres a video

I would return this........Has to be an electrical issue. After only 3 months should be covered with warranty.

There may be a safety switch for the bag cover and it may not be engaged properly. Try taking the bag cover off or open it and try closing it again.

Hi there! Your battery may need to be reset. Try depleting the battery. Run the vacuum until it completely shuts off, then re-charge for a full 24 hours. Hope this helps out! If you still have questions you feel free to reach out to us here on Fixya, Facebook.com/dirtdevil, or Twitter @DirtDevil.

visit searspartsdirect.com making sure you use the dashes, the spaces etc in the model number. I found 2 manuals that can be downloaded. I used 08-632-0

Not sure which model is yours? Check your product for its unique model number or contact us at 1-800-252-1698.

Hello! There is no other part that goes on the motor shaft after the belt is put on. The tension of the belt keeps the belt from slipping off. If you have a brand new belt that keeps slipping off you may not have the correct belt for the vacuum. Be sure you replace with a genuine Dirt Devil belt and the specified belt style for your particular unit. Hope this helps! If you still need assistance feel free to reach out to us here on Fixya, Facebook.com/dirtdevil, or Twitter @DirtDevil.

Hi! Below are step-by-step instructions on how to change the bag on your vacuum. This vacuum takes a Dirt Devil Type D replacement bag. I have included a link to the instruction manual, as well as a link where you may go to purchase replacement bags for your vacuum. 1. To Remove: squeeze front panel release lever and pull towards you. 2. Grasp cardboard collar of paper bag with both hands and pull past raised locking tabs on the dirt tube. Dispose of old paper bag. 3. Important: Extend bag away from hole before installing. Press in opening to clear paper away from hole. 4. To Install: Push cardboard collar past raised locking tabs on the dirt tube with both hands. Be sure paper bag is fully extended and tucked in at the top and bottom. 5. Replace front panel by putting the two bottom tabs in the slots on the vacuum. Push front panel so release lever attaches. http://bit.ly/1DEkilx Type 3 Pack Hope this helps!

Hi, if the warranty is still valid , do not try to solve the problem yourself, best to return to dealer. All the luck.

Hi there! The vacuum is equipped with a thermal protector sensor that will automatically shut the motor down if it reaches a certain temperature. This is usually caused by either a clog or a filter that needs to be cleaned or replaced. Make sure you check both the hoses for clogs and clean all filters properly. If a filter is really dirty it may be time to replace it. Hope this was helpful!

Normally fairly simple.............1)Remove the bottom plastic cover. Should be 2 or 3 screws. 2) Pull the bar out (along with the belt) 3) Put new belt around the bar on the smooth surface. 3) Put bar back in (It goes a certain way, but easy to tell by the ends of the bar 4) Stretch the belt back to the small round metal pole. It should be tight, so sometimes takes a litlle muscle.

Hello there! The motor gets hot when there is an airflow constriction. This is usually caused by a clog or a filter that needs to be cleaned or replaced. Try checking your vacuum for clogs and cleaning and replacing the filters if needed. Hope this helps! If not please reach out to us here on Fixya and provide your model number so that we may better assist you.

Sounds like you are not getting a good seal. Make sure it is locking tight. You may have to use some duct tape! Some have a seal around the top where the cannister is affixed. Check this, may need to get a new rubber seal.

Filters can clog quickly or you may have a clog somewhere which will reduce airflow causing the motor to overheat and shut off. It will come back on after it cools down. If that is the problem you may need to clean or replace the filters. If that does not solve it I would take it to a Royal warranty repair shop.

I have a Dyson and was having a similar problem some time back. I found out these bagless systems still have a filter that picks up the fine dust to keep it contained. Find out where yours is located and beat the dust out of it really good or just replace it. Hope this helps.

Some vacuums have a reset button you can push. Some have a fuse in the power line that may have blown. You will have to follow the power all the way through the vacuum checking the voltage at each switch, connection, etc. I often unhook the power & neutral wires from the motor and hook up a power cord with connectors on the end directly to the motor to make sure the motor is good. You must be very knowledgable with motors, switches, electrical testing, etc. If not this repair is best left to a professional.

Hello! Follow the link below to view the instruction manual for the CE7900. http://dirtdevil.com/file/160/

I have seen where so do not know that certain pieces of vac and be taken apart. Open and unscrew to look inside to see whats loose causing that problem.

it might be the roller its self