Top 20 Dirt Devil UD40270RM Quick Power Compact Bagless Upright Vacuum Refurbished,Lightweight,Fold Down Handle,HEPAFiltration,5 Position Height Adjustment Questions & Answers


Lubricate each end of the roller brush with motor oil. Bearings inside the roller brush need lubrication for the brush to turn easily. Remove any pieces of thread that have wrapped around the roller brush. If it does not spin after doing the above steps, then either the belt is slipping or the bearings are severely damaged in the roller brush. Then you need either a smaller belt or a new roller brush.

Dirt Devil... | 258 views | 1 helpful votes


Is there suction at the hose? If not it is either blocked or the suction fan is broken. If there is, then there is a blockage in the pickup section, something is lodged across the channel after the brushes and before the place where the hose plugs in.

I think there is a safety switch to prevent it from running with the canister out so hard to check for suction at the top of the motor/suction fan. Make sure nothing is over that part under the canister too! If you can figure out how to bypass the safety switch (if there is one), you should have good suction where the canister sets on top of the motor base.

Dirt Devil... | 322 views | 0 helpful votes


its clogged. find out where and clear it out

Dirt Devil... | 13 views | 0 helpful votes


maybe the battery is pooched? ng

Dirt Devil... | 20 views | 0 helpful votes


Request the manual from Dirt Devil.

Dirt Devil... | 16 views | 0 helpful votes


Onn tv has no sound

Dirt Devil... | 93 views | 0 helpful votes


You'll need a model/part number to be able to figure out what belt you need.

Dirt Devil... | 144 views | 0 helpful votes


Almost always you have a blockage somewhere. It is not always easy to get to each and every nook and cranny of the suction passageways.
Typically some piece is blocking, and that means reduced air flow, which means overheated motor... Do not run for long with this blockage.
Think in terms of air flow, your answer will likely be there.

Cheers,
Doc

Dirt Devil... | 119 views | 0 helpful votes


Refer to YouTube video online.

Dirt Devil... | 154 views | 0 helpful votes


they have been having alot of problems with these models. if its brand new, take it back. don't try and work on it yourself, it will void the warranty

Dirt Devil... | 148 views | 0 helpful votes


Sure, take the machine apart. Cut off the bad part of wire. Strip insulation to same as what's inside. Remove old original & wire in the new.

Dirt Devil... | 118 views | 0 helpful votes


I know of no "resart button"

Dirt Devil... | 138 views | 0 helpful votes


Hi Kathy,

Click this you tube tutorial to see how they open the vacuum with the same model that you are looking for.

https://www.youtube.com/watch?v=yG29klTuWxc

Dirt Devil... | 602 views | 0 helpful votes


You didnt specify the model number, so I'll limit my answer to most common.

On most upright vacs, you disconnect the hose running to the floor pickup and attach the crevice tool (or whatever else you have) to the end of this hose. You then continue cleaning with the hose end atrachment.

I would imaging the Dirt Devil Edge Wedge is similar.

Dirt Devil... | 107 views | 0 helpful votes


It sounds like there is a clog in the hose itself if you have no suction from the end. If it is bagless remove the canister from the machine or if it is a bagged machine remove the bag. If you have a shop vac attach the hose from the shop vac to the end of the hose of the dirt devil and try to suck the obstruction out that way. Sometimes it is possible to remove the clog this way. You can tell if you have suction from the debris port to the bag or the canister. If not you may need to use a snake or coat hanger to pull the clog through.

Dirt Devil... | 113 views | 0 helpful votes


sometimes vacs get to old ,, you can find the same model or purchase a new one here>>>www.discountbargainprices.com

Dirt Devil... | 156 views | 0 helpful votes


Hi there, a few different solutions....
flip it over and remove the screws, take a piece of paper and draw a diagram of how the screws are placed. place the screws on the paper as they were in the vacuum. remove any screws needed to free the brush, remove trash and her from the brush- scissors will help a bit- put it back together and give it a try, the other solution it to check the motor that spins the brush it may be dealt driven or gear driven or a direct drive- I don't wanna tell you more because you are a consumer and dirt devil did not want you taking it apart because its unsafe if your not sure what your doing and id feel bad if something happen to you..
https://www.6ya.com/mr.mike

Dirt Devil... | 75 views | 0 helpful votes

Not finding what you are looking for?
Dirt Devil UD40270RM Quick Power Compact Bagless Upright Vacuum Refurbished,Lightweight,Fold Down Handle,HEPAFiltration,5 Position Height Adjustment Logo

2 questions posted

Ask a Question

Usually answered in minutes!

Top Dirt Devil Vacuums Experts

Tim Venetis

Level 2 Expert

260 Answers

The Knight
The Knight

Level 3 Expert

76466 Answers

Randy Schumann
Randy Schumann

Level 2 Expert

410 Answers

Are you a Dirt Devil Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Dirt Devil Vacuums

  • Dirt Devil Vacuums

Most Popular Question

fix vacuum brush will not spin

  • Vacuums
Loading...